- 您現在的位置：買賣IC網 > PDF目錄67762 > M37534M4-XXXGP 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32 PDF資料下載
參數資料
| 型號： | M37534M4-XXXGP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP32 |
| 封裝： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件頁數： | 25/56頁 |
| 文件大?。?/td> | 699K |
| 代理商： | M37534M4-XXXGP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
7534 Group
Rev.3.00
Oct 23, 2006
page 31 of 53
REJ03B0099-0300
Serial I/O2 operation
By writing to the serial I/O2 register(address 003116) the serial I/O2
counter is set to “7”.
After writing, the SDATA pin outputs data every time the transfer clock
shifts from a high to a low level. And, as the transfer clock shifts from
a low to a high, the SDATA pin reads data, and at the same time the
contents of the serial I/O2 register are shifted by 1 bit.
When the internal clock is selected as the transfer clock source, the
following operations execute as the transfer clock counts up to 8.
Serial I/O2 counter is cleared to “0”.
Transfer clock stops at an “H” level.
Interrupt request bit is set.
Shift completion flag is set.
Also, the SDATA pin is in a high impedance state after the data trans-
fer is complete. Refer to Figure 34.
When the external clock is selected as the transfer clock source, the
interrupt request bit is set as the transfer clock counts up to 8, but
external control of the clock is required since it does not stop. Notice
that the SDATA pin is not in a high impedance state on the completion
of data transfer.
Fig. 34 Serial I/O2 timing (LSB first)
D0
Note : When the internal clock is selected as the transfer and the direction register of P1 3/SDATA pin is set to the input mode,
Synchronous clock
Serial I/O2 register
write signal
Transfer clock
(Note)
SDATA at serial I/O2
input receive
SDATA at serial I/O2
output transmit
Serial I/O2 interrupt request bit set
D1
D2
D3
D4
D5
D6
D7
the SDATA pin is in a high impedance state after the data transfer is completed.
相關PDF資料 |
PDF描述 |
|---|---|
| M37630E4T-XXXFP | 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44 |
| M37630E4FS | 8-BIT, UVPROM, 10 MHz, MICROCONTROLLER, CQCC80 |
| M37641M8-XXXHP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37641F8HP | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37643F8FP | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37534M4-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37534RSS | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37536E8SP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37536M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37536M4-XXXSP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。