- 您現在的位置：買賣IC網 > PDF目錄45035 > M37542F8SP 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32 PDF資料下載
參數資料
| 型號： | M37542F8SP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDIP32 |
| 封裝： | 8.9 X 28 MM, 1.78 MM PITCH, PLASTIC, SDIP-32 |
| 文件頁數： | 53/124頁 |
| 文件大?。?/td> | 1238K |
| 代理商： | M37542F8SP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁當前第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁
7542 Group
Rev.3.03
Jul 11, 2008
Page 32 of 117
REJ03B0006-0303
(4) Pulse width measurement mode
In the pulse width measurement mode, the pulse width of the sig-
nal input to P14/CNTR0 pin is measured.
The operation of Timer X can be controlled by the level of the sig-
nal input from the CNTR0 pin.
When the CNTR0 active edge switch bit is “0”, the signal selected
by the timer X count source selection bit is counted while the input
signal level of CNTR0 pin is “H”. The count is stopped while the
pin is “L”. Also, when the CNTR0 active edge switch bit is “1”, the
signal selected by the timer X count source selection bit is
counted while the input signal level of CNTR0 pin is “L”. The count
is stopped while the pin is “H”.
Timer X can stop counting by setting “1” to the timer X count stop
bit in any mode.
Also, when Timer X underflows, the timer X interrupt request bit is
set to “1”.
Note on Timer X is described below;
■ Note on Timer X
(1) CNTR0 interrupt active edge selection-1
CNTR0 interrupt active edge depends on the CNTR0 active edge
switch bit.
When this bit is “0”, the CNTR0 interrupt request bit is set to “1” at
the falling edge of CNTR0 pin input signal. When this bit is “1”, the
CNTR0 interrupt request bit is set to “1” at the rising edge of
CNTR0 pin input signal.
(2) CNTR0 interrupt active edge selection-2
According to the setting value of CNTR0 active edge switch bit,
the interrupt request bit may be set to “1”.
When not requiring the interrupt occurrence synchronized with
these setting, take the following sequence.
Set the corresponding interrupt enable bit to “0” (disabled).
Set the active edge switch bit.
Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
Set the corresponding interrupt enable bit to “1” (enabled).
Fig. 29 Structure of timer X mode register
Fig. 30 Timer count source set register
Timer X mode register
(TXM : address 002B16, initial value: 0016)
CNTR0 active edge switch bit
0 : Interrupt at falling edge
Count at rising edge
(in event counter mode)
1 : Interrupt at rising edge
Count at falling edge
(in event counter mode)
Timer X operating mode bits
b1 b0
0
0 : Timer mode
0
1 : Pulse output mode
1
0 : Event counter mode
1
1 : Pulse width measurement mode
Not used (return “0” when read)
Timer X count stop bit
0 : Count start
1 : Count stop
b7
b0
P03/TXOUT output valid bit
0 : Output invalid (I/O port)
1 : Output valid (Inverted CNTR0 output)
b7
b0
Timer X count source selection bits
b1 b0
0
0 : f(XIN)/16
0
1 : f(XIN)/2
1
0 : f(XIN) (Note 1)
1
1 : Not available
Notes 1: f(XIN) can be used as timer X count source when using
a ceramic resonator or on-chip oscillator.
Do not use it at RC oscillation.
2: On-chip oscillator can be used when the on-chip oscillator
is enabled by bit 3 of CPUM.
Timer count source set register
(TCSS : address 002A16, initial value: 0016)
Timer B count source selection bits
b7 b6 b5
0
0 : f(XIN)/16
0
1 : f(XIN)/2
0
1
0 : f(XIN)/32
0
1
1 : f(XIN)/64
1
0
0 : f(XIN)/128
1
0
1 : f(XIN)/256
1
0 : Timer A underflow
1
1 : Not available
Timer A count source selection bits
b4 b3 b2
0
0 : f(XIN)/16
0
1 : f(XIN)/2
0
1
0 : f(XIN)/32
0
1
1 : f(XIN)/64
1
0
0 : f(XIN)/128
1
0
1 : f(XIN)/256
1
0 : On-chip oscillator output (Note 2)
1
1 : Not available
相關PDF資料 |
PDF描述 |
|---|---|
| M37542F8FP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37542F8GP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37542F4GP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PQFP32 |
| M37542F4FP | 8-BIT, FLASH, 8 MHz, MICROCONTROLLER, PDSO36 |
| M37542M4-XXXHP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQCC36 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37542F8SP#U0 | 制造商:Renesas Electronics Corporation 功能描述:MCU 4.0/5.5V 32K PB-FREE 32-SDIP - Trays |
| M37542M2-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXHP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37542M2-XXXSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。