- 您現在的位置：買賣IC網 > PDF目錄45036 > M37547G4-XXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 PDF資料下載
參數資料
| 型號： | M37547G4-XXXFP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO36 |
| 封裝： | 8.40 X 15 MM, 0.80 MM PITCH, PLASTIC, SSOP-36 |
| 文件頁數： | 33/99頁 |
| 文件大小： | 1029K |
| 代理商： | M37547G4-XXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
REJ03B0156-0122
Rev.1.22
Mar 31, 2009
page 37 of 94
7547 Group
Input capture
7547 group has 2-input capture channels. Each channel (0 and 1)
has the same function and can be used to capture count value of
either Timer A or Timer B.
The source timer for each channel is selected by setting value of
the capture x (x = 0, 1) timer source bit. Timer A and Timer B can
be selected for the source timer to each channel, respectively.
To use each capture channel, set the capture x input port bits and
set the port direction register corresponding to capture channel to
input mode.
The input capture circuit retains the count value of selected timer
when external trigger is input. The timer count value is retained to
the capture latch x0 when rising edge is input and is retained to
the capture latch x1 when falling edge is input.
The count value of timer can be retained by software by capture y
(y = 00, 01, 10, 11) software trigger bit too. When “1” is set to this
bit, count value of timer is retained to the corresponded capture
latch.
When reading from the capture y software trigger bit is executed,
“0” is read out.
The latest status of capture latch can be confirmed by reading of
the capture x status bit. This bit indicates the capture latch which
latest data is in.
The valid trigger edge for capture interrupt is set by the capture x
interrupt edge selection bits. (Regardless of the setting value of
capture x interrupt edge selection bits, timer count values for both
edges are retained to the capture latch.)
Each capture input has the noise filter circuit that judges continu-
ous 4-time same level with sampling clock to be valid. The
sampling clock of noise filter is set by the capture x noise filter
clock selection bits.
Reading from the register for each channel is controlled by setting
value of the capture register read pointer. Reading from each reg-
ister is in the following order;
1.Set the value of the corresponded input capture channel to the
capture register read pointer.
2.Read from the capture register (low-order) and capture register
(high-order).
■ Notes on Input Capture
If the capture trigger is input while the capture register (low-order
and high-order) is in read, captured value is changed between
high-order reading and low-order reading. Accordingly, some
countermeasure by program is recommended, for example
comparing the values that twice of read.
When CPU operation clock source is XIN oscillation and the on-
chip-oscillator is selected for Timer A count source, Timer A
cannot be used for the capture source timer.
Timer B cannot be used for the capture source timer when the
system is in the following state;
CPU operation clock source: XIN oscillation
Timer B count source: Timer A underflow
Timer A count source: On-chip oscillator output
When writing “1” to capture latch x0 (x1) software trigger bit of
capture latch x0 and x1 at the same time, or external trigger and
software trigger occur simultaneously, the set value of capture x
status bit is undefined.
When setting the interrupt active edge selection bit and noise fil-
ter clock selection bit of external interrupt CAP0, CAP1, the
interrupt request bit may be set to “1”.
When not requiring the interrupt occurrence synchronized with
these setting, take the following sequence.
Set the corresponding interrupt enable bit to “0” (disabled).
Set the interrupt edge selection bit or noise filter clock selection bit.
Set the corresponding interrupt request bit to “0” after 1 or more
instructions have been executed.
Set the corresponding interrupt enable bit to “1” (enabled).
When the capture interrupt is used as the interrupt for return
from stop mode, set the capture x noise filter clock selection bits
to “00 (Filter stop)”.
相關PDF資料 |
PDF描述 |
|---|---|
| M37548G2-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20 |
| M37548G2FP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20 |
| M37548G1FP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO20 |
| M37549G1-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24 |
| M37549G3-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37548G1FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37548G1-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37548G2FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37548G2-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37548G3FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。