SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3825 Group
48
Table 16. Recommended operating conditions (Standard, One time PROM version)
(VCC = 2.5 to 5.5 V, Ta = –20 to 85°C, unless otherwise noted)
–20
20
40
–10
10
20
–0.5
–5.0
5.0
–0.1
–2.5
2.5
5.0
Note 1: The total output current is the sum of all the currents flowing through all the applicable ports. The total average current is an aver-
age value measured over 100 ms. The total peak current is the peak value of all the currents.
2: The peak output current is the peak current flowing in each port.
3: The average output current is an average value measured over 100 ms.
4: When the oscillation frequency has a duty cycle of 50%.
5: When using the microcomputer in low-speed mode, make sure that the sub-clock input oscillation frequency on condition that
f(XCIN) < f(XIN)/3.
“H” total peak output current
P00–P07, P10–P17, P20–P27, P30–P37 (Note 1)
“H” total peak output current
P40–P47,P50–P57, P60–P67, P71–P77, P80, P81
(Note 1)
“L” total peak output current
P00–P07, P10–P17, P20–P27, P30–P37 (Note 1)
“L” total peak output current
P40–P47,P50–P57, P60–P67, P80, P81 (Note 1)
“L” total peak output current
P71–P77 (Note 1)
“H” total average output current P00–P07,P10–P17, P20–P27, P30–P37 (Note 1)
“H” total average output current P40–P47, P50–P57, P60–P67, P71–P77, P80, P81
(Note 1)
“L” total average output current P00–P07, P10–P17, P20–P27, P30–P37 (Note 1)
“L” total average output current P40–P47, P50–P57, P60–P67, P80, P81 (Note 1)
“L” total average output current P71–P77 (Note 1)
“H” peak output current
P00–P07, P10–P15, P30–P37 (Note 2)
“H” peak output current
P16, P17, P20–P27, P40–P47, P50–P57, P60–P67,
P71–P77, P80, P81 (Note 2)
“L” peak output current
P00–P07, P10–P15, P30–P37 (Note 2)
“L” peak output current
P16, P17, P20–P27, P40–P47, P50–P57, P60–P67,
P70–P77, P80, P81 (Note 2)
“H” average output current
P00–P07, P10–P15, P30–P37 (Note 3)
“H” average output current
P16, P17, P20–P27, P40–P47, P50–P57, P60–P67,
P71–P77, P80, P81 (Note 3)
“L” average output current
P00–P07, P10–P15, P30–P37 (Note 3)
“L” average output current
P16, P17, P20–P27, P40–P47, P50–P57, P60–P67,
P71–P77, P80, P81 (Note 3)
Input frequency for timers X and Y
(duty cycle 50%)
Main clock input oscillation frequency
(Note 4)
Sub-clock input oscillation frequency (Note 4, 5)
ΣIOH(peak)
ΣIOL(peak)
ΣIOH(avg)
ΣIOL(avg)
IOH(peak)
IOL(peak)
IOH(avg)
IOL(avg)
f(CNTR0)
f(CNTR1)
f(XIN)
f(XCIN)
Symbol
Parameter
Limits
Min.
mA
MHz
kHz
Unit
Typ.
Max.
(4.0 V
≤ VCC ≤ 5.5 V)
(VCC
≤ 4.0 V)
High-speed mode
(4.0 V
≤ VCC ≤ 5.5 V)
High-speed mode
(VCC
≤ 4.0 V)
Middle-speed mode
4.0
(2VCC)
–4
8.0
(4VCC)
–8
8.0
50
32.768
10