- 您現在的位置：買賣IC網 > PDF目錄370912 > M38273E2MXXXFP (Mitsubishi Electric Corporation) SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER PDF資料下載
參數資料
| 型號： | M38273E2MXXXFP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 24/70頁 |
| 文件大?。?/td> | 1112K |
| 代理商： | M38273E2MXXXFP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
24
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
3827 Group
MITSUBISHI MICROCOMPUTERS
Timer 1, Timer 2, Timer 3
Timer 1, timer 2, and timer 3 are 8-bit timers. The count source for
each timer can be selected by timer 123 mode register. The timer
latch value is not affected by a change of the count source. How-
ever, because changing the count source may cause an
inadvertent count down of the timer. Therefore, rewrite the value of
timer whenever the count source is changed.
G
Timer 2 write control
If the timer 2 write control bit is “0”, when the value is written in the
address of timer 2, the value is loaded in the timer 2 and the latch
at the same time.
If the timer 2 write control bit is “1”, when the value is written in the
address of timer 2, the value is loaded only in the latch. The value
in the latch is loaded in timer 2 after timer 2 underflows.
G
Timer 2 output control
When the timer 2 (T
OUT
) is output enabled, an inversion signal
from the T
OUT
pin is output each time timer 2 underflows.
In this case, set the port shared with the T
OUT
pin to the output.
I
Notes on timer 1 to timer 3
When the count source of timer 1 to 3 is changed, the timer count-
ing value may be changed large because a thin pulse is generated
in count input of timer . If timer 1 output is selected as the count
source of timer 2 or timer 3, when timer 1 is written, the counting
value of timer 2 or timer 3 may be changed large because a thin
pulse is generated in timer 1 output.
Therefore, set the value of timer in the order of timer 1, timer 2 and
timer 3 after the count source selection of timer 1 to 3.
Fig. 20 Structure of timer 123 mode register
T
OUT
output active edge switch bit
0 : Start at “H” output
1 : Start at “L” output
T
OUT
/
φ
output control bit
0 : T
OUT
/
φ
output disabled
1 : T
OUT
/
φ
output enabled
Timer 2 write control bit
0 : Write data in latch and counter
1 : Write data in latch only
Timer 2 count source selection bit
0 : Timer 1 output
1 : f(X
IN
)/16
(or f(X
CIN
)/16 in low-speed mode)
Timer 3 count source selection bit
0 : Timer 1 output
1 : f(X
IN
)/16
(or f(X
CIN
)/16 in low-speed mode)
Timer 1 count source selection bit
0 : f(X
IN
)/16
(or f(X
CIN
)/16 in low-speed mode)
1 : f(X
CIN
)
Not used (return “0” when read)
Timer 123 mode register
(T123M :address 0029
16
)
Note :
Internal clock
φ
is X
CIN
/2 in the low-speed mode.
b7
b0
相關PDF資料 |
PDF描述 |
|---|---|
| M38273E2MXXXFS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38273E2MXXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38273E2MXXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38273E3MXXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38272E1MXXXFP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M3828 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 1000' |
| M3828 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 500' |
| M3828 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 100' |
| M3828 BK199 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 3000=3000' |
| M3829 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 4COND 16AWG BLK 1000' |
發布緊急采購，3分鐘左右您將得到回復。