參數資料
型號： M38273E4MXXXFP
廠商： Mitsubishi Electric Corporation
英文描述： Dual Low-Power, Rail-to-Rail Input/Output Operational Amplifier 20-LCCC -55 to 125
中文描述： 單芯片8位CMOS微機
文件頁數： 22/70頁
文件大?。?/td> 1112K
代理商： M38273E4MXXXFP
22
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
3827 Group
MITSUBISHI MICROCOMPUTERS
Timer X mode register
(TXM : address 0027
16
)
Timer X write control bit
0 : Write value in latch and counter
1 : Write value in latch only
Real time port control bit
0 : Real time port function invalid
1 : Real time port function valid
P5
2
data for real time port
P5
3
data for real time port
Timer X operating mode bits
b5 b4
0 0 : Timer mode
0 1 : Pulse output mode
1 0 : Event counter mode
1 1 : Pulse width measurement mode
CNTR
0
active edge switch bit
0 : Count at rising edge in event counter mode
Start from “H” output in pulse output mode
Measure “H” pulse width in pulse width
measurement mode
Falling edge active for CNTR
0
interrupt
1 : Count at falling edge in event counter mode
Start from “L” output in pulse output mode
Measure “L” pulse width in pulse width
measurement mode
Rising edge active for CNTR
0
interrupt
Timer X stop control bit
0 : Count start
1 : Count stop
b7
b0
Timer X
Timer X is a 16-bit timer that can be selected in one of four modes
and can be controlled the timer X write and the real time port by
setting the timer X mode register.
(1) Timer Mode
The timer counts f(X
IN
)/16 (or f(X
CIN
)/16 in low-speed mode).
(2) Pulse Output Mode
Each time the timer underflows, a signal output from the CNTR
0
pin is inverted. Except for this, the operation in pulse output mode
is the same as in timer mode. When using a timer in this mode, set
the port shared with the CNTR
0
pin to input.
(3) Event Counter Mode
The timer counts signals input through the CNTR
0
pin.
Except for this, the operation in event counter mode is the same
as in timer mode. When using a timer in this mode, set the port
shared with the CNTR
0
pin to input.
(4) Pulse Width Measurement Mode
The count source is f(X
IN
)/16 (or f(X
CIN
)/16 in low-speed mode). If
CNTR
0
active edge switch bit is “0”, the timer counts while the in-
put signal of CNTR
0
pin is at “H”. If it is “1”, the timer counts while
the input signal of CNTR
0
pin is at “L”. When using a timer in this
mode, set the port shared with tha CNTR
0
pin to input.
G
Timer X write control
If the timer X write control bit is “0”, when the value is written in the
address of timer X, the value is loaded in the timer X and the latch
at the same time.
If the timer X write control bit is “1”, when the value is written in the
address of timer X, the value is loaded only in the latch. The value
in the latch is loaded in timer X after timer X underflows.
If the value is written in latch only, unexpected value may be set in
the high-order counter when the writing in high-order latch and the
underflow of timer X are performed at the same timing.
I
Note on CNTR
0
interrupt active edge
selection
CNTR
0
interrupt active edge depends on the CNTR
0
active edge
switch bit.
G
Real time port control
While the real time port function is valid, data for the real time port
are output from ports P5
2
and P5
3
each time the timer X
underflows. (However, if the real time port control bit is changed
from “0” to “1”, data are output without the timer X.) When the data
for the real time port is changed while the real time port function is
valid, the changed data are output at the next underflow of timer X.
Before using this function, set the corresponding port direction
registers to output mode.
Fig. 18 Structure of timer X mode register
相關PDF資料
PDF描述
M38273E4MXXXFS Dual Low-Power, Rail-to-Rail Input/Output Operational Amplifier 8-CDIP -55 to 125
M38273E4MXXXGP Dual Low-Power, Rail-to-Rail Input/Output Operational Amplifier 8-CDIP -55 to 125
M38273E4MXXXHP Dual Low-Power, Rail-to-Rail Input/Output Operational Amplifier 10-CFP -55 to 125
M38273E5MXXXFP Dual Low-Power, Rail-to-Rail Input/Output Operational Amplifier 20-LCCC -55 to 125
M38273E5MXXXFS Dual Low-Power, Rail-to-Rail Input/Output Operational Amplifier 10-CFP -55 to 125
相關代理商/技術參數
參數描述
M3828 BK001 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 1000'
M3828 BK002 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 500'
M3828 BK005 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 100'
M3828 BK199 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 3000=3000'
M3829 BK001 制造商:Alpha Wire Company 功能描述:CBL 4COND 16AWG BLK 1000'
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*