- 您現在的位置：買賣IC網 > PDF目錄370909 > M38274E5-XXXHP (Mitsubishi Electric Corporation) CONN HOUSING 22PS .100 SGL PDF資料下載
參數資料
| 型號： | M38274E5-XXXHP |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | CONN HOUSING 22PS .100 SGL |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 37/70頁 |
| 文件大?。?/td> | 1112K |
| 代理商： | M38274E5-XXXHP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁當前第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
37
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3827 Group
VOLTAGE MULTIPLIER (3 TIMES)
The voltage multiplier performs threefold boosting. This circuit in-
puts a reference voltage for boosting from LCD power input pin
V
L1
. (However, when using a 1/2 bias, connect V
L1
and V
L2
and
apply voltage by external resistor division.)
Set each bit of the segment output enable register and the LCD
mode register in the following order for operating the voltage mul-
tiplier.
1. Set the segment output enable bits (bits 0 to 5) of the seg-
ment output enable register to “0” or “1.”
2. Set the duty ratio selection bits (bits 0 and 1), the bias con-
trol bit (bit 2), the LCD circuit divider division ratio selection
bits (bits 5 and 6), and the LCDCK count source selection
bit (bit 7) of the LCD mode register to “0” or “1.”
3. Set the LCD output enable bit (bit 6) of the segment output
enable register to “1.”
4. Set the voltage multiplier control bit (bit 4) of the LCD mode
register to “1.”
When voltage is input to the V
L1
pin during operating the voltage
multiplier, voltage that is twice as large as V
L1
occurs at the V
L2
pin, and voltage that is three times as large as V
L1
occurs at the
V
L3
pin.
When using the voltage multiplier, apply 1.3 V
≤
Voltage
≤
2.3 V to
the V
L1
pin.
When not using the voltage multiplier,apply proper voltage to the
LCD power input pins (V
L1
–V
L3
). Then set the LCD output enable
bit to “1.”
When the LCD output enable bit is set to “0,” the V
CC
voltage is
applied to the V
L3
pin inside of this microcomputer.
The voltage multiplier control bit (bit 4 of the LCD mode register)
controls the voltage multiplier.
Fig. 40 Example of circuit at each bias
Table 8 Bias control and applied voltage to V
L1
–V
L3
Bias value
1/3 bias
Voltage value
V
L3
=V
LCD
V
L2
=2/3 V
LCD
V
L1
=1/3 V
LCD
Note 1:
V
LCD
is the maximum value of supplied voltage for the
LCD panel.
Bias Control and Applied Voltage to LCD
Power Input Pins
To the LCD power input pins (V
L1
–V
L3
), apply the voltage shown in
Table 8 according to the bias value.
Select a bias value by the bias control bit (bit 2 of the LCD mode
register).
1/2 bias
V
L3
=V
LCD
V
L2
=V
L1
=1/2 V
LCD
V
L3
V
L2
C
2
C
1
V
L1
1/3 bias
when using the voltage multiplier
V
L3
V
L2
C
2
C
1
V
L1
1/3 bias
when not using the voltage multiplier
Open
Open
R2
R1
R3
R1=R2=R3
Contrast control
V
L3
V
L2
C
2
C
1
V
L1
1/2 bias
Open
Open
R4
R5
R4=R5
Contrast control
V
CC
V
CC
PX
X
相關PDF資料 |
PDF描述 |
|---|---|
| M38274E6-XXXFS | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38274E6-XXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38274E6-XXXHP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M38274E8-XXXFS | CONN POLARIZING PLUG |
| M38274E8-XXXGP | SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M3828 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 1000' |
| M3828 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 500' |
| M3828 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 100' |
| M3828 BK199 | 制造商:Alpha Wire Company 功能描述:CBL 3COND 16AWG BLK 3000=3000' |
| M3829 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 4COND 16AWG BLK 1000' |
發布緊急采購，3分鐘左右您將得到回復。