參數資料
型號： M38501D1
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 15/52頁
文件大?。?/td> 807K
代理商： M38501D1
15
3850 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
TIMERS
The 3850 group has four timers: timer X, timer Y, timer 1, and
timer 2.
The division ratio of each timer or prescaler is given by 1/(n + 1),
where n is the value in the corresponding timer or prescaler latch.
All timers are count down. When the timer reaches “00
16
”, an un-
derflow occurs at the next count pulse and the corresponding
timer latch is reloaded into the timer and the count is continued.
When a timer underflows, the interrupt request bit corresponding
to that timer is set to “1”.
Timer 1 and Timer 2
The count source of prescaler 12 is the oscillation frequency
which is selected by timer 12 count source selection bit. The out-
put of prescaler 12 is counted by timer 1 and timer 2, and a timer
underflow sets the interrupt request bit.
Timer X and Timer Y
Timer X and Timer Y can each select in one of four operating
modes by setting the timer XY mode register.
(1) Timer Mode
The timer counts the count source selected by Timer count source
selection bit.
(2) Pulse Output Mode
The timer counts the count source selected by Timer count source
selection bit. Whenever the contents of the timer reach “00
16
”, the
signal output from the CNTR
0
(or CNTR
1
) pin is inverted. If the
CNTR
0
(or CNTR
1
) active edge selection bit is “0”, output begins
at “ H”.
If it is “1”, output starts at “L”. When using a timer in this mode, set
the corresponding port P2
7
( or port P4
0
) direction register to out-
put mode.
(3) Event Counter Mode
Operation in event counter mode is the same as in timer mode, ex-
cept that the timer counts signals input through the CNTR
0
or
CNTR
1
pin.
When the CNTR
0
(or CNTR
1
) active edge selection bit is “0”, the
rising edge of the CNTR
0
(or CNTR
1
) pin is counted.
When the CNTR
0
(or CNTR
1
) active edge selection bit is “1”, the
falling edge of the CNTR
0
(or CNTR
1
) pin is counted.
(4) Pulse Width Measurement Mode
If the CNTR
0
(or CNTR
1
) active edge selection bit is “0”, the timer
counts the selected signals by the count source selection bit while
the CNTR
0
(or CNTR
1
) pin is at “H”. If the CNTR
0
(or CNTR
1
) ac-
tive edge selection bit is “1”, the timer counts it while the CNTR
0
(or CNTR
1
) pin is at “L”.
The count can be stopped by setting “1” to the timer X (or timer Y)
count stop bit in any mode. The corresponding interrupt request
bit is set each time a timer underflows.
Fig. 12 Structure of timer XY mode register
I
Note
When switching the count source by the timer 12, X and Y count
source bit, the value of timer count is altered in unconsiderable
amount owing to generating of a thin pulses in the count input
signals.
Therefore, select the timer count source before set the value to
the prescaler and the timer.
Fig. 13 Structure of timer count source selection register
Timer count source selection register
(TCSS : address 0028
16
)
b7
b0
Timer X count source selection bit
IN
CIN
0 : f(X
IN
)/16 (f(X
CIN
)/)/16 at low-speed mode)
Timer Y count source selection bit
0 : f(X
IN
)/16 (f(X
CIN
)/16 at low-speed mode)
1 : f(X
IN
)/2 (f(X
CIN
)/2 at low-speed mode)
Timer 12 count source selection bit
0 : f(X
IN
)/16 (f(X
CIN
)/16 at low-speed mode)
1 : f(X
CIN
)
Not used (returns “0” when read)
Timer X count stop bit
0: Count start
1: Count stop
Timer XY mode register
(TM : address 0023
16
)
Timer Y operating mode bit
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
CNTR
1
active edge selection bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
Timer Y count stop bit
0: Count start
1: Count stop
b7
CNTR
0
active edge selection bit
0: Interrupt at falling edge
Count at rising edge in event
counter mode
1: Interrupt at rising edge
Count at falling edge in event
counter mode
b0
Timer X operating mode bit
0 0: Timer mode
0 1: Pulse output mode
1 0: Event counter mode
1 1: Pulse width measurement mode
相關PDF資料
PDF描述
M38503M4-219SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4-237SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4-263FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4-266FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38501E1H-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES
M38501E1H-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES
M38501E1H-XXXSS 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES
M38501E1-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES
M38501E1-XXXSP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT CISC SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*