參數資料
型號: M38503MXH
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述: 單芯片8位CMOS微機
文件頁數: 43/86頁
文件大?。?/td> 1193K
代理商: M38503MXH
43
3850 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Fig. 47 Program flowchart
Program Command (40
16
)
Program operation starts when the command code
40
16
is written
in the first bus cycle. Then, if the address and data to program are
written in the 2nd bus cycle, program operation (data programming
and verification) will start.
Whether the write operation is completed can be confirmed by read-
ing the status register or the RY/BY status flag. When the program
starts, the read status register mode is accessed automatically and
the content of the status register is read into the data bus (D0
D7).
The status register bit 7 (SR7) is set to
0
at the same time the write
operation starts and is returned to
1
upon completion of the write
operation. In this case, the read status register mode remains active
until the read array command (FF
16
) is written.
The RY/BY status flag is
0
during write operation and
1
when the
write operation is completed as is the status register bit 7.
At program end, program results can be checked by reading the sta-
tus register.
Erase All Blocks Command (20
16
/20
16
)
By writing the command code
20
16
in the first bus cycle and the
confirmation command code
20
16
in the second bus cycle that fol-
lows, the system starts erase all blocks( erase and erase verify).
Whether the erase all blocks command is terminated can be con-
firmed by reading the status register or the RY/BY status flag. When
the erase all blocks operation starts, the read status register mode is
accessed automatically and the content of the status register can be
read out. The status register bit 7 (SR7) is set to
0
at the same time
the erase operation starts and is returned to
1
upon completion of
the erase operation. In this case, the read status register mode re-
mains active until the read array command (FF
16
) is written.
The RY/BY status flag is
0
during erase operation and
1
when the
erase operation is completed as is the status register bit 7.
At erase all blocks end, erase results can be checked by reading the
status register. For details, refer to the section where the status reg-
ister is detailed.
Block Erase Command (20
16
/D0
16
)
By writing the command code
20
16
in the first bus cycle and the
confirmation command code
D0
16
in the second bus cycle that
follows to the block address of a flash memory block, the system
initiates a block erase (erase and erase verify) operation.
Whether the block erase operation is completed can be confirmed
by reading the status register or the RY/BY status flag. At the same
time the block erase operation starts, the read status register mode
is automatically entered, so the content of the status register can be
read out. The status register bit 7 (SR7) is set to
0
at the same time
the block erase operation starts and is returned to
1
upon comple-
tion of the block erase operation. In this case, the read status regis-
ter mode remains active until the read array command (FF
16
) is writ-
ten.
The RY/BY status flag is
0
during block erase operation and
1
when the block erase operation is completed as is the status register
bit 7.
After the block erase operation is completed, the status register can
be read out to know the result of the block erase operation. For de-
tails, refer to the section where the status register is detailed.
Fig. 48 Erase flowchart
Start
Write
40
16
Status register
read
Program
completed
NO
YES
Write address
Write data
SR4=0
Program
error
NO
YES
SR7=1
or
RY/BY=1
Write
Write 20
16
20
16
/D0
16
Block address
Erase completed
NO
YES
Start
Write
SR5=0
Erase error
YES
NO
20
16
:Erase all blocks
D0
16
:Block erase
SR7=1
or
RY/BY=1
Status register
read
相關PDF資料
PDF描述
M38507E8SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4H-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4H-XXXSP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4H SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38513M4 Hook-Up Wire; Conductor Size AWG:26; No. Strands x Strand Size:7 x 34; Jacket Color:Dark Blue; Approval Bodies:UL, CSA; Approval Categories:UL AWM Style 1061; CSA AWM; Conductor Material:Copper RoHS Compliant: Yes
相關代理商/技術參數
參數描述
M38504E6FP 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 24K 42-SSOP - Trays
M38504E6FP#U0 功能描述:MCU 4.0/5.5V 24K PB-FREE 42-SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI,I²C,IEBus,IrDA,SIO,UART/USART 外圍設備:DMA,POR,PWM,WDT 輸入/輸出數:121 程序存儲器容量:384KB(384K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b,D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
M38504M6202F 制造商:Panasonic Industrial Company 功能描述:SUB ONLY IC
M38504M6211F 制造商:Panasonic Industrial Company 功能描述:IC SUB FOR P-M38504M6202F
M38507ARLSS 功能描述:M-SUPPORT TOOL RoHS:否 類別:編程器,開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF)