參數資料
型號: M38507E8FP
廠商: Mitsubishi Electric Corporation
英文描述: SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述: 單芯片8位CMOS微機
文件頁數: 55/86頁
文件大?。?/td> 1193K
代理商: M38507E8FP
55
3850 Group (Spec. H)
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Standard serial I/O mode
The standard serial I/O mode inputs and outputs the software com-
mands, addresses and data needed to operate (read, program,
erase, etc.) the internal flash memory. This I/O is clock synchronized
serial. This modes require a purpose-specific peripheral unit.
The standard serial I/O mode is different from the parallel I/O mode
in that the CPU controls flash memory rewrite (uses the CPU's re-
write mode), rewrite data input and so forth. The standard serial I/O
mode is started by connecting
H
to the P4
1
(INT
0
) pin and
H
to the
CNV
SS
pin (when V
CC
= 4.5 V to 5.5 V, connect to V
CC
; when V
CC
=
2.7 V to 4.5 V, supply 4.5 V to 5.5 V to Vpp from an external source),
and releasing the reset operation. (In the ordinary command mode,
set CNVss pin to
L
level.)
This control program is written in the boot ROM area when the prod-
uct is shipped from Mitsubishi. Accordingly, make note of the fact
that the standard serial I/O mode cannot be used if the boot ROM
area is rewritten in the parallel I/O mode. Figure 56 shows the pin
connections for the standard serial I/O mode. Serial data I/O uses SI/
O1 data serially in 8-bit units.
To use standard serial I/O mode. The operation uses the four SI/O1
pins S
CLK
, RxD, TxD and S
RDY1
(BUSY). The S
CLK
pin is the trans-
fer clock input pin through which an external transfer clock is input.
The TxD pin is for CMOS output. The S
RDY1
(BUSY) pin outputs an
L
level when ready for reception and an
H
level when reception
starts.
In the standard serial I/O mode, only the user ROM area indicated in
Figure 44 can be rewritten. The boot ROM cannot.
In the standard serial I/O mode, a 7-byte ID code is used. When
there is data in the flash memory, commands sent from the periph-
eral unit (programmer) are not accepted unless the ID code
matches.
Overview of standard serial I/O mode
In standard serial I/O mode, software commands, addresses and
data are input and output between the MCU and peripheral units
(serial programer, etc.) using 4-wire clock-synchronized serial I/O
(SI/O1).
In reception, software commands, addresses and program data are
synchronized with the rise of the transfer clock that is input to the
S
CLK
pin, and are then input to the MCU via the RxD pin. In transmis-
sion, the read data and status are synchronized with the fall of the
transfer clock, and output from the TxD pin.
The TxD pin is for CMOS output. Transfer is in 8-bit units with LSB
first.
When busy, such as during transmission, reception, erasing or pro-
gram execution, the S
RDY1
(BUSY) pin is
H
level. Accordingly, al-
ways start the next transfer after the S
RDY1
(BUSY) pin is
L
level.
Also, data and status registers in memory can be read after inputting
software commands. Status, such as the operating state of the flash
memory or whether a program or erase operation ended success-
fully or not, can be checked by reading the status register. Here fol-
lowing are explained software commands, status registers, etc.
相關PDF資料
PDF描述
M38503E4SS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4 SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503MXH SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38507E8SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38503M4H-XXXFP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38507F8AFP#U1 功能描述:IC 740/3850 MCU FLASH 42SSOP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI,I²C,IEBus,IrDA,SIO,UART/USART 外圍設備:DMA,POR,PWM,WDT 輸入/輸出數:121 程序存儲器容量:384KB(384K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b,D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
M38507F8AFP#W1 制造商:Renesas Electronics Corporation 功能描述:MCU 3/5V 32K PB-FREE 42-SSOP T&R - Tape and Reel
M38507F8FP 制造商:Renesas Electronics Corporation 功能描述:MCU 8-Bit 740 CISC 32KB Flash 5V 42-Pin SSOP 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays
M38507F8FP#U1 制造商:Renesas Electronics Corporation 功能描述:MCU 8BIT 740 CISC 32KB FLASH 5V 42SSOP - Trays
M38507F8FP#W1 制造商:Renesas Electronics Corporation 功能描述:FLASH 8-BIT 2.7 TO 5.5V PBFREE