參數資料
型號： M38512M4
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 30/61頁
文件大?。?/td> 904K
代理商： M38512M4
30
3851 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
(2) START condition generating procedure using multi-master
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 5.
:
LDA —
(Taking out of slave address value)
SEI
(Interrupt disabled)
BBS 5, S1, BUSBUSY (BB flag confirming and branch pro-
cess)
BUSFREE:
STA S0
(Writing of slave address value)
LDM #$F0, S1
(Trigger of START condition generating)
CLI
(Interrupt enabled)
:
BUSBUSY:
CLI
(Interrupt enabled)
:
2. Use “Branch on Bit Set” of “BBS 5, $002D, –” for the BB flag
confirming and branch process.
3. Use “STA $2B, STX $2B” or “STY $2B” of the zero page ad-
dressing instruction for writing the slave address value to the
I
2
C data shift register.
4. Execute the branch instruction of above 2 and the store instruc-
tion of above 3 continuously shown the above procedure
example.
5. Disable interrupts during the following three process steps:
BB flag confirming
Writing of slave address value
Trigger of START condition generating
When the condition of the BB flag is bus busy, enable interrupts
immediately.
(3) RESTART condition generating procedure
1. Procedure example (The necessary conditions of the generat-
ing procedure are described as the following 2 to 4.)
Execute the following procedure when the PIN bit is “0.”
:
LDM #$00, S1
(Select slave receive mode)
LDA —
(Taking out of slave address value)
SEI
(Interrupt disabled)
STA S0
(Writing of slave address value)
LDM #$F0, S1
(
Trigger of RESTART condition generating
)
CLI
(Interrupt enabled)
:
2. Select the slave receive mode when the PIN bit is “0.” Do not
write “1” to the PIN bit. Neither “0” nor “1” is specified for the
writing to the BB bit.
The TRX bit becomes “0” and the S
DA
pin is released.
3. The S
CL
pin is released by writing the slave address value to
the I
2
C data shift register.
4. Disable interrupts during the following two process steps:
Writing of slave address value
Trigger of RESTART condition generating
(4) Writing to I
2
C status register
Do not execute an instruction to set the PIN bit to “1” from “0” and
an instruction to set the MST and TRX bits to “0” from “1” simulta-
neously. It is because it may enter the state that the S
CL
pin is
released and the S
DA
pin is released after about one machine
cycle. Do not execute an instruction to set the MST and TRX bits
to “0” from “1” simultaneously when the PIN bit is “1.” It is because
it may become the same as above.
(5) Process of after STOP condition generating
Do not write data in the I
2
C data shift register S0 and the I
2
C sta-
tus register S1 until the bus busy flag BB becomes “0” after
generating the STOP condition in the master mode. It is because
the STOP condition waveform might not be normally generated.
Reading to the above registers do not have the problem.
I
Precautions when using multi-master I
2
C-BUS
interface
(1) Read-modify-write instruction
The precautions when the read-modify-write instruction such as
SEB, CLB etc. is executed for each register of the multi-master
I
2
C-BUS interface are described below.
I
2
C data shift register (S0: address 002B
16
)
When executing the read-modify-write instruction for this regis-
ter during transfer, data may become a value not intended.
I
2
C address register (S0D: address 002C
16
)
When the read-modify-write instruction is executed for this regis-
ter at detecting the STOP condition, data may become a value
not intended. It is because H/W changes the read/write bit
(RBW) at the above timing.
I
2
C status register (S1: address 002D
16
)
Do not execute the read-modify-write instruction for this register
because all bits of this register are changed by H/W.
I
2
C control register (S1D: address 002E
16
)
When the read-modify-write instruction is executed for this regis-
ter at detecting the START condition or at completing the byte
transfer, data may become a value not intended. Because H/W
changes the bit counter (BC0-BC2) at the above timing.
I
2
C clock control register (S2: address 002F
16
)
The read-modify-write instruction can be executed for this regis-
ter.
I
2
C START/STOP condition control register (S2D: address
0030
16
)
The read-modify-write instruction can be executed for this regis-
ter.
相關PDF資料
PDF描述
M388504E6SP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M388504E6SS SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M3850 Single Chip 8 Bits Microcomputer(8位單片機)
M388504E6FP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M38867E8A-XXXHP SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
相關代理商/技術參數
參數描述
M38513E4FP 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 24K/640B RAM, W/A-D, I2C, L - Rail/Tube
M38513E4FP#U0 功能描述:IC 740 MCU ROM 16K 42SSOP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 產品培訓模塊:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 標準包裝:1 系列:M16C™ M32C/80/87 核心處理器:M32C/80 芯體尺寸:16/32-位 速度:32MHz 連通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外圍設備:DMA，POR，PWM，WDT 輸入/輸出數:121 程序存儲器容量:384KB（384K x 8） 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:24K x 8 電壓 - 電源 (Vcc/Vdd):3 V ~ 5.5 V 數據轉換器:A/D 34x10b，D/A 2x8b 振蕩器型:內部 工作溫度:-20°C ~ 85°C 封裝/外殼:144-LQFP 包裝:托盤 產品目錄頁面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87
M38514E6FP 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 24K/640B RAM, W/A-D, I2C, L - Rail/Tube
M38514E6SP 制造商:Renesas Electronics Corporation 功能描述:SLIM740 OTP 24K/640B RAM, W/A-D, I2C, L - Rail/Tube
M38517T-ADS 功能描述:DEV TMP TRGT BRD FOR M38517RSS & RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 標準包裝:1 系列:- 附件類型:適配器板 適用于相關產品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*