參數資料
型號： M41T11MH6
廠商： STMICROELECTRONICS
元件分類： 時鐘/數據恢復及定時提取
英文描述： 0 TIMER(S), REAL TIME CLOCK, PDSO28
封裝： 0.330 INCH, SNAPHAT, PLASTIC, SOH-28
文件頁數： 3/24頁
文件大?。?/td> 355K
代理商： M41T11MH6
11/24
M41T11
CLOCK OPERATION
The eight byte clock register (see Table 3) is used
to both set the clock and to read the date and time
from the clock, in a binary coded decimal format.
Seconds, Minutes, and Hours are contained within
the first three registers. Bits D6 and D7 of clock
register 2 (Hours Register) contain the CENTURY
ENABLE Bit (CEB) and the CENTURY Bit (CB).
Setting CEB to a '1' will cause CB to toggle, either
from '0' to '1' or from '1' to '0' at the turn of the cen-
tury (depending upon its initial state). If CEB is set
to a '0', CB will not toggle. Bits D0 through D2 of
register 3 contain the Day (day of week). Registers
4, 5 and 6 contain the Date (day of month), Month
and Years. The final register is the Control Regis-
ter (this is described in the Clock Calibration sec-
tion). Bit D7 of register 0 contains the STOP Bit
(ST). Setting this bit to a '1' will cause the oscillator
to stop. If the device is expected to spend a signif-
icant amount of time on the shelf, the oscillator
may be stopped to reduce current drain. When re-
set to a '0' the oscillator restarts within one second.
Note: In order to guarantee oscillator start-up after
the initial power-up, set the ST Bit to a '1,' then re-
set this bit to a '0.' This sequence enables a “kick
start” circuit which aids the oscillator start-up dur-
ing worst case conditions of voltage and tempera-
ture.
The seven Clock Registers may be read one byte
at a time, or in a sequential block. The Control
Register (Address location 7) may be accessed in-
dependently. Provision has been made to assure
that a clock update does not occur while any of the
seven clock addresses are being read. If a clock
address is being read, an update of the clock reg-
isters will be delayed by 250ms to allow the read
to be completed before the update occurs. This
will prevent a transition of data during the read.
Note: This 250ms delay affects only the clock reg-
ister update and does not alter the actual clock
time.
Table 3. Register Map
Keys: S = SIGN Bit
FT = FREQUENCY TEST Bit
ST = STOP Bit
OUT = Output level
X = Don’t care
CEB = Century Enable Bit
CB = Century Bit
Note: 1. When CEB is set to '1', CB will toggle from '0' to '1' or from '1' to '0' every 100 years (dependent upon the initial value set).
When CEB is set to '0', CB will not toggle.
Address
Data
Function/Range
BCD Format
D7
D6
D5
D4
D3
D2
D1
D0
0
ST
10 Seconds
Seconds
00-59
1
X
10 Minutes
Minutes
00-59
2
CEB (1)
CB
10 Hours
Hours
Century/Hours
0-1/00-23
3
XXX
XX
Day
01-07
4
X
10 Date
Date
01-31
5
X
10 M.
Month
01-12
6
10 Years
Years
Year
00-99
7
OUT
FT
S
Calibration
Control
相關PDF資料
PDF描述
M41T11M6 0 TIMER(S), REAL TIME CLOCK, PDSO8
M41T11MH6TR 0 TIMER(S), REAL TIME CLOCK, PDSO28
M41T56M6E 0 TIMER(S), REAL TIME CLOCK, PDSO8
M41T56M6F 0 TIMER(S), REAL TIME CLOCK, PDSO8
M41T56MH6 0 TIMER(S), REAL TIME CLOCK, PDSO28
相關代理商/技術參數
參數描述
M41T11MH6E 功能描述:實時時鐘 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T11MH6F 功能描述:實時時鐘 Serial 512 (64x8) RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
M41T11MH6F-CUT TAPE 制造商:ST 功能描述:M41T11 Series 2 to 5.5 V Serial I2C Real Time Clock Surface Mount - SOH-28
M41T11MH6TR 制造商:STMicroelectronics 功能描述:REAL TIME CLOCK SERL 64BYTE 28PIN SOH - Tape and Reel
M41T11SH 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:512 bit 64b x8 Serial Access TIMEKEEPER SRAM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*