參數資料
型號： M50FW040K5P
廠商： 意法半導體
英文描述： 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory
中文描述： 4兆位（512 KB的× 8，均勻塊）3 - V電源供電的閃存固件樞紐
文件頁數： 12/53頁
文件大?。?/td> 278K
代理商： M50FW040K5P
Signal descriptions
M50FW040
12/53
2
Signal descriptions
There are two different bus interfaces available on this part. The active interface is selected
before power-up or during Reset using the Interface Configuration Pin, IC.
The signals for each interface are discussed in the
Firmware hub (FWH) signal descriptions
section and the
Address/Address multiplexed (A/A Mux) signal descriptions
section below.
The supply signals are discussed in the
Supply signal descriptions
section below.
2.1
Firmware hub (FWH) signal descriptions
For the Firmware Hub (FWH) Interface see <Blue>Figure 1., Logic diagram (FWH
interface), and <Blue>Table 1., Signal names (FWH interface).
2.1.1
Input/Output communications (FWH0-FWH3)
All Input and Output Communication with the memory take place on these pins. Addresses
and Data for Bus Read and Bus Write operations are encoded on these pins.
2.1.2
Input communication frame (FWH4)
The Input Communication Frame (FWH4) signals the start of a bus operation. When Input
Communication Frame is Low, V
IL
, on the rising edge of the Clock a new bus operation is
initiated. If Input Communication Frame is Low, V
IL
, during a bus operation then the
operation is aborted. When Input Communication Frame is High, V
IH
, the current bus
operation is proceeding or the bus is idle.
2.1.3
Identification inputs (ID0-ID3)
The Identification Inputs select the address that the memory responds to. Up to 16
memories can be addressed on a bus. For an address bit to be ‘0’ the pin can be left floating
or driven Low, V
IL
; an internal pull-down resistor is included with a value of R
IL
. For an
address bit to be ‘1’ the pin must be driven High, V
IH
; there will be a leakage current of I
LI2
through each pin when pulled to V
IH
; see <Blue>Table 18.
By convention the boot memory must have address ‘0000’ and all additional memories take
sequential addresses starting from ‘0001’.
2.1.4
General-purpose inputs (FGPI0-FGPI4)
The General Purpose Inputs can be used as digital inputs for the CPU to read. The General
Purpose Inputs Register holds the values on these pins. The pins must have stable data
from before the start of the cycle that reads the General Purpose Input Register until after
the cycle is complete. These pins must not be left to float, they should be driven Low, V
IL,
or
High, V
IH
.
相關PDF資料
PDF描述
M50FW040K5TG 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory
M50FW040K5TP 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory
M50FW040N5G 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory
M50FW040N5P 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory
M50FW040N5TG 4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory
相關代理商/技術參數
參數描述
M50FW040K5T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW040K5TG 功能描述:閃存 SERIAL FLASH RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M50FW040K5TP 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4-Mbit (512 Kb x8, uniform block) 3-V supply firmware hub Flash memory
M50FW040N 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit 512Kb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW040N1 功能描述:閃存 3.6V 4M (512Kx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*