- 您現在的位置：買賣IC網 > PDF目錄377830 > M50FW080K5P (意法半導體) 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory PDF資料下載
參數資料
| 型號： | M50FW080K5P |
| 廠商： | 意法半導體 |
| 英文描述： | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| 中文描述： | 8兆1兆× 8，統一座3V電源閃存固件集線器 |
| 文件頁數： | 24/56頁 |
| 文件大?。?/td> | 292K |
| 代理商： | M50FW080K5P |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
Command interface
M50FW080
24/55
4.4
Program command
The Program command can be used to program a value to one address in the memory array
at a time. Two Bus Write operations are required to issue the command; the second Bus
Write cycle latches the address and data in the internal state machine and starts the
Program/Erase Controller. Once the command is issued subsequent Bus Read operations
read the Status Register. See the section on the Status Register for details on the definitions
of the Status Register bits.
If the address falls in a protected block then the Program operation will abort, the data in the
memory array will not be changed and the Status Register will output the error.
During the Program operation the memory will only accept the Read Status Register
command and the Program/Erase Suspend command. All other commands will be ignored.
Typical Program times are given in
Table 14
.
Note that the Program command cannot change a bit set at ‘0’ back to ‘1’ and attempting to
do so will not cause any modification on its value. One of the Erase commands must be
used to set all of the bits in the block to ‘1’.
See
Figure 18
, for a suggested flowchart on using the Program command.
4.5
Quadruple Byte Program command
The Qua-druple Byte Program Command can be only used in A/A Mux mode to program
four adjacent bytes in the memory array at a time. The four bytes must differ only for the
addresses A0 and A10. Programming should not be attempted when V
PP
is not at V
PPH
.
The operation can also be executed if V
PP
is below V
PPH
, but result could be uncertain. Five
Bus Write operations are required to issue the command. The second, the third and the
fourth Bus Write cycle latches respectively the address and data of the first, the second and
the third byte in the internal state machine. The fifth Bus Write cycle latches the address and
data of the fourth byte in the internal state machine and starts the Program/Erase Controller.
Once the command is issued subsequent Bus Read operations read the Status Register.
See the section on the Status Register for details on the definitions of the Status Register
bits.
During the Quadruple Byte Program operation the memory will only accept the Read Status
register command and the Program/Erase Suspend command. All other commands will be
ignored. Typical Quadruple Byte Program times are given in
Table 8
.
Note that the Quadruple Byte Program command cannot change a bit set to ‘0’ back to ‘1’
and attempting to do so will not cause any modification on its value. One of the Erase
commands must be used to set all of the bits in the block to ‘1’.
See
Figure 19
, Quadruple Byte Program Flowchart and Pseudo Code, for a suggested
flowchart on using the Quadruple Byte Program command.
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW080K5TP | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080N5P | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080N5TP | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB5P | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB5TP | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50FW080K5T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080K5TG | 功能描述:閃存 8 Mbit RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50FW080K5TP | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080N | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080N1 | 功能描述:閃存 3.6V 8M (1Mx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。