參數資料
型號： M50FW080N5P
廠商： 意法半導體
英文描述： 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
中文描述： 8兆1兆× 8，統一座3V電源閃存固件集線器
文件頁數： 27/56頁
文件大?。?/td> 292K
代理商： M50FW080N5P
M50FW080
Command interface
27/55
Table 9.
Commands
(1)
1.
X Don’t Care, PA Program Address, PD Program Data, A
1,2,3,4
Consecutive Addresses, BA Any address
in the Block.
Command
C
Bus Write operations
1st
2nd
3rd
4th
5th
Addr Data Addr Data Addr Data Addr Data Addr Data
Read Memory Array
(2)
2.
Read Memory Array
. After a Read Memory Array command, read the memory as normal until another
command is issued.
1
X
FFh
Read Status Register
(3)
3.
Read Status Register
. After a Read Status Register command, read the Status Register as normal until
another command is issued.
1
X
70h
Read Electronic
Signature
(4)
4.
Read Electronic Signature
. After a Read Electronic Signature command, read Manufacturer Code,
Device Code until another command is issued.
1
X
90h
1
X
98h
Program
(5)
5.
Block Erase, Program
. After these commands read the Status Register until the command completes
and another command is issued.
2
X
40h
PA
PD
2
X
10h
PA
PD
Quadruple Byte Program
(6)
6.
Quadruple Byte Program.
This command is only valid in A/A Mux mode. Addresses A
, A
, A
and A
4
must be consecutive addresses differing only for address bit A0 and A10. After this command read the
Status Register until the command completes and another command is issued.
5
X
30h
A
1
PD
A
2
PD
A
3
PD
A
4
PD
Chip Erase
(7)
7.
Chip Erase.
This command is only valid in A/A Mux mode. After this command read the Status Register
until the command completes and another command is issued.
2
X
80h
X
10h
Block Erase
(5)
2
X
20h
BA
D0h
Clear Status Register
(8)
8.
Clear Status Register
. After the Clear Status Register command bits 1, 3, 4 and 5 in the Status Register
are reset to ‘0’.
1
X
50h
Program/Erase Suspend
(9)
9.
Program/Erase Suspend
. After the Program/Erase Suspend command has been accepted, issue Read
Memory Array, Read Status Register, Program (during Erase suspend) and Program/Erase resume
commands.
1
X
B0h
Program/Erase Resume
(10)
10.
Program/Erase Resume
. After the Program/Erase Resume command the suspended Program/Erase
operation resumes, read the Status Register until the Program/Erase Controller completes and the
memory returns to Read Mode.
1
X
D0h
Invalid/Reserved
(11)
11.
Invalid/Reserved
. Do not use Invalid or Reserved commands.
1
X
00h
1
X
01h
1
X
60h
1
X
2Fh
1
X
C0h
相關PDF資料
PDF描述
M50FW080N5TP 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB5P 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB5TP 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50LPW002 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory
M50LPW002K 2 Mbit 256Kb x8, Boot Block 3V Supply Low Pin Count Flash Memory
相關代理商/技術參數
參數描述
M50FW080N5T 制造商:Micron Technology Inc 功能描述:
M50FW080N5TG 功能描述:閃存 8 Mbit RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M50FW080N5TP 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
M50FW080NB1G 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*