參數資料
型號: M50LPW080
廠商: 意法半導體
英文描述: 8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
中文描述: 8兆1兆× 8,統一座3V電源低引腳數快閃記憶體
文件頁數: 20/44頁
文件大小: 641K
代理商: M50LPW080
M50LPW080
20/44
Program Suspend Status (Bit 2).
The Program
Suspend Status bit indicates that a Program oper-
ation has been suspended and is waiting to be re-
sumed. The Program Suspend Status should only
be considered valid when the Program/Erase
Controller Status bit is ‘1’ (Program/Erase Control-
ler inactive); after a Program/Erase Suspend com-
mand is issued the memory may still complete the
operation rather than entering the Suspend mode.
When the Program Suspend Status bit is ‘0’ the
Program/Erase Controller is active or has complet-
ed its operation; when the bit is ‘1’ a Program/
Erase Suspend command has been issued and
the memory is waiting for a Program/Erase Re-
sume command.
When a Program/Erase Resume command is is-
sued the Program Suspend Status bit returns to
‘0’.
Block Protection Status (Bit 1).
The Block Pro-
tection Status bit can be used to identify if the Pro-
gram or Block Erase operation has tried to modify
the contents of a protected block. When the Block
Protection Status bit is to ‘0’ no Program or Block
Erase operations have been attempted to protect-
ed blocks since the last Clear Status Register
command or hardware reset; when the Block Pro-
tection Status bit is ‘1’ a Program or Block Erase
operation has been attempted on a protected
block.
Once it is set to ‘1’ the Block Protection Status bit
can only be reset to ‘0’ by a Clear Status Register
command or a hardware reset. If it is set to ‘1’ it
should be reset before a new Program or Block
Erase command is issued, otherwise the new
command will appear to fail.
Using the A/A Mux Interface the Block Protection
Status bit is always ‘0’.
Reserved (Bit 0).
Bit 0 of the Status Register is
reserved. Its value should be masked.
Table 11. Status Register Bits
Note: 1. For Program operations during Erase Suspend Bit 6 is ‘1’, otherwise Bit 6 is ‘0’.
Operation
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Program active
‘0’
X
(1)
‘0’
‘0’
‘0’
‘0’
‘0’
Program suspended
‘1
X
(1)
‘0’
‘0’
‘0’
‘1’
‘0’
Program completed successfully
‘1’
X
(1)
‘0’
‘0’
‘0’
‘0’
‘0’
Program failure due to V
PP
Error
‘1’
X
(1)
‘0’
‘0’
‘1’
‘0’
‘0’
Program failure due to Block Protection (LPC Interface only)
‘1’
X
(1)
‘0’
‘0’
‘0’
‘0’
‘1’
Program failure due to cell failure
‘1’
X
(1)
‘0’
‘1’
‘0’
‘0’
‘0’
Erase active
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
Block Erase suspended
‘1’
‘1’
‘0’
‘0’
‘0’
‘0’
‘0’
Erase completed successfully
‘1’
‘0’
‘0’
‘0’
‘0’
‘0’
‘0’
Erase failure due to V
PP
Error
‘1’
‘0’
‘0’
‘0’
‘1’
‘0’
‘0’
Block Erase failure due to Block Protection (LPC Interface
only)
‘1’
‘0’
‘0’
‘0’
‘0’
‘0’
‘1’
Erase failure due to failed cell(s)
‘1’
‘0’
‘1’
‘0’
‘0’
‘0’
‘0’
相關PDF資料
PDF描述
M50LPW080K 8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW080K5G 8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW080K5T 8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW080K5TG 8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW080K1 8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
相關代理商/技術參數
參數描述
M50LPW080K 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW080K1 功能描述:閃存 3.6V 8M (1Mx8) RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel
M50LPW080K1G 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW080K1T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory
M50LPW080K1TG 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8 Mbit 1Mb x8, Uniform Block 3V Supply Low Pin Count Flash Memory