M61530FP
Rev.1.0, Sep.19.2003, page 10 of 18
Electrical characteristics
Unless otherwise noted, Ta = 25
°
C, Vcc = 9 V, f = 1 kHz, input gain control = 0 dB, bass boost = off, trim/master
volume = 0 dB, FL/FR output SW = on, SL/SR VOL input SW = SL/SR input, LFE MIXS SW = on, SW MIX= off,
output gain control = 0 dB
Item
Symbol
Limits
Min.
Max.
Unit
Condition
Typ.
Power
supply
I/O
Circuit current
IACC
14
25
mA
When no signal is detected, current flows to pin 16
Max. input
voltage
VIM1
1.6
2.0
Vrms
Pins 2, 37, 40, and 41: Input, pins 1, 38, 39, and 42:
Output, RL = 10 k
, THD = 1%
Pins 6, 10, and 13: Input, pins 5, 9, and 12: Output, RL =
10 k
, THD = 1%
Pin 14:
Input, pin 22: Output, RL = 10 k
, THD = 5%, f =
100 kHz
VIM2
0.8
1.0
Vrms
VIM3
1.6
2.0
Vrms
Absolute max.
input voltage
Max. output
voltage
AVIM
2.0
Note
Vrms
Pins 3, 7, 14, and 15: Input
VOM1
1.8
2.4
Vrms
Pins 6 and 10: Input, pins 29 and 26: Output, RL = 10 k
,
THD = 5%, bass boost = on, f = 100 Hz
Pin 13: Input, pin 25: Output, RL = 10 k
, THD = 5%
Gain between pins 14 and 22, Vi = 0.5 Vrms, FLAT, f = 100
Hz
VOM2
VOM3
1.6
1.4
2.0
1.8
Vrms
Vrms
Bypass gain
GV1
+2.3
+4.3
+6.3
dB
Gain from pins 6 to 29, pin 10 to 26, and pins 13 to 25, Vi =
0.5 Vrms, FLAT
Gain from pins 2 to 32 and 41 to 34, Vi = 0.5 Vrms, FLAT
GV2
-2
0
+2
dB
Output noise
voltage
GV3
Vno1
-2
0
6.0
+2
12.0
dB
μ
Vrms
μ
Vrms
Gain from pin 14 to 22, Vi = 0.5 Vrms, FLAT, f = 100 Hz
DIN-Audio, when no signal is
present, Rg = 0 for pins 6 and
10, pins 29 and 26 are outputs
SL/SR ch volume = -
∞
dB
C ch volume = 0 dB
C ch volume = -
∞
dB
2.5
8.0
Vno2
6.0
10.0
μ
Vrms
μ
Vrms
2.0
4.0
DIN-Audio, when no signal is
present, Rg = 0 for pin 13, pin 25
is an output
Vno3
6.5
6.5
16.0
16.0
μ
Vrms
μ
Vrms
LFE ch volume = 0 dB
LFE ch volume = -
∞
dB
DIN-Audio, when no signal is
detected, Rg = 0 for pin 14, pin
22 is an output, SW ch LPF:
fc=300 Hz
Pins 6 and 10: input, pins 29 and 26: output, bandwidth:
400 Hz to 30 kHz, Vo = 0.5 Vrms, RL = 10 k
Pin 13: input, pin 25: output, bandwith: 400 Hz to 30 kHz,
Vo = 0.5 Vrms, RL = 10 k
Pin 14: input, pin 22: output, 30-kHz low-pass filter, Vo =
0.5 Vrms, RL = 10 k
, output gain control = 0 dB, when
AGC is not operating, f = 100 Hz
THD1
0.003
0.2
%
Total
harmonic
distortion rate
THD2
0.003
0.1
%
THD3
0.008
0.2
%
THD4
2
%
Pin 14: input, pin 22: output, 30-kHz low-pass filter, RL = 10
k
, Vi = 700 mVrms, f = 100 Hz, when AGC is operating,
output gain control = + 12 dB
Vo = 1 Vrms, pins 22, 25, 26, and 29 are outputs, JIS-A,
volume = -
∞
Volume max.
attenuation
ATT
-100
-87
dB