- 您現在的位置：買賣IC網 > PDF目錄359085 > M62244FP (Renesas Technology Corp.) Li-ion Battery Charge Controller IC PDF資料下載
參數資料
| 型號： | M62244FP |
| 廠商： | Renesas Technology Corp. |
| 英文描述： | Li-ion Battery Charge Controller IC |
| 中文描述： | 鋰離子電池充電控制IC |
| 文件頁數： | 14/18頁 |
| 文件大?。?/td> | 239K |
| 代理商： | M62244FP |
M62244FP
Rev.1.0, Sep.19.2003, page 14 of 17
11. Setting the voltages
The recharge-start voltage, adapter-detection voltage 1, and adapter-detection voltage 2 can be adjusted to desired
thresholds through the connection of external resistors that adjust the voltages on the Vrchg, Vadp1, and Vadp2
pins, respectively.
When a pin is open, the corresponding voltage is the IC’s internal setting as specified in the electrical
characteristics.
When the Vadp1 pin, Vadp2 pin, and Vrchg pin are open-circuit, the output voltage is the VBG voltage (constant
voltage source used inside the IC) divided by 20 k
and 100 k
, as shown in section 2, Pin-Internal Equivalent
Circuits. The settings are given below.
<Method of setting>
Let the detection voltages when the recharge-start voltage, adapter-detection voltage 1, and adapter-detection
voltage 2 pins are open-circuit be Vrchg_o (V), Vadp1_o (V), and Vadp2_o (V), respectively, and the required
detection-voltage values be Vrchg_c (V), Vadp1_c (V), and Vadp2_c (V), respectively. The voltage to be applied
to each of the adjustment pins is then obtained by the equations under (1), (2), and (3) below.
(1) Recharge-start voltage
Voltage on the Vrchg pin
(open-circuit)
Vrchg_o
Voltage setting on the Vrchg pin (V) =
×
Vrchg_c
(2) Adapter-detection voltage 1
Voltage on the Vadp1 pin
(open-circuit)
Vadp1_o
Voltage setting on the Vadp1 pin (V) =
×
Vadp1_c
(3) Adapter-detection voltage 2
Voltage on the Vadp2 pin
(open-circuit)
Vadp2_o
Voltage setting on the Vadp2 pin (V) =
×
Vadp2_c
Desired detection values are obtained by using external resistors to apply the voltages obtained by the above
equations to the corresponding pins.
Either connect a resistor between the adjustment pin and ground, or connect one resistor between the Vcvref pin
and adjustment pin and another between the adjustment pin and ground. Note, however, when using the Vcvref pin,
that –5 mA is specified as the maximum load-current for this pin. Take care in selecting the resistor values.
Note: In the descriptions of pins Vrchg, Vadp1, and Vadp2 pins in section 1, Description of pins, decibel units are
used to describe how the voltages on these pins set the detection voltages. The values used in the above
equations are calculated after changing the values as shown below. The calculation is on the assumption
that each pin carries the rated voltage of 1.0 V when in its open-circuit state.
(4) Recharge-start voltage
Vrchg_c
Vrchg_o
Voltage on the Vrchg pin
=
Voltage on the Vrchg pin
(open-circuit)
3.95
→
11.8dB
相關PDF資料 |
PDF描述 |
|---|---|
| M62343GP | 8-Bit, 3-Channel D/A Converter (Buffered) |
| M62383FP | 5 V Composite Type D-A Converter |
| M63028 | Spindle Motor and 5ch Actuator Driver |
| M63151FP | Polygon Scanner Motor Driver (DMOS Driver) |
| M63154AFP | 3-PHASE BRUSHLESS MOTOR DRIVER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M62251 | 制造商:Mitsubishi Electric 功能描述:ELECTRONIC COMPONENT |
| M62253 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:LITHIUM ION BATTERY CHARGER CONTROL IC |
| M62253AGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Charge Control IC for Li-Ion Batteries |
| M62253BGP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:Charge Control IC for Li-Ion Batteries |
| M62253FP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:LITHIUM ION BATTERY CHARGER CONTROL IC |
發布緊急采購，3分鐘左右您將得到回復。