MITSUBISHI IC
M64894FP/GP
S
(TV)
SERIAL INPUT PLL FREQUENCY SYNTHESIZER FOR TV/VCR
3
DESCRIPTION OF PIN
ABSOLUTE MAXIMUM RATINGS
(Ta=-20
°
C to +75
°
C, unless otherwise noted)
RECOMMENDED OPERATING CONDITIONS
(Ta=-20
°
C to +75
°
C, unless otherwise noted)
Pin No.
1
2
3
4
5
6
7
8
Symbol
Pin name
Function
fin
GND
V
CC1
V
CC2
BS4
BS3
BS2
BS1
Prescaler input
GND
Power supply voltage 1
Power supply voltage 2
Input for the VCO frequency.
Ground to 0V.
Power supply voltage terminal. 5.0V
Power supply for band switching, Vcc
±
0.5V
to 13.2V
1
Band switching outputs
PNP open collector method is used.
When the band switching data is "H", the output is ON.
When it is "L", the output is OFF.
9
Vin
Filter input
(Charge pump output)
This is the output terminal for the LPF input and charge pump output. When the
phase of the programmable divider output (f 1/N) is ahead compared to the
reference frequency (fref), the "source" current state becomes active.
If it is behind, the "sink" current becomes active.
If the phases are the same, the high impedance state becomes active.
This supplies the tuning voltage.
Power supply voltage for tuning voltage 28 to 35V
A/D conversion of the input voltage.
In control byte data input, the programmabule freq. Divider output and reference
freq. output is selected by the test mode.
Data is read into the shift register when the clock signal falls.
Input for band SW and programmable freq. divider set up.
In lead mode, itoutputs lock detector output and power down flagand a state of 5
level A/D converter.
Chip address sets it up with the input condition of terminal.
10
11
Vtu
V
CC3
Tuning output
Power supply voltage 3
12
ADC/ftest
AD converter input/
Test port
13
SCL
Clock input
14
SDA
Data input
15
ADS
Address switching input
This is connected to the
crystal oscillator
16
Xin
4.0MHz crystal oscillator is connected.
Symbol
V
CC1
V
CC2
V
CC3
V
I
V
O
Parameter
Conditions
Ratings
6.0
14.4
36.0
6.0
6.0
Unit
V
V
V
V
V
Supply voltage 1
Supply voltage 2
Supply voltage 3
Input voltage
Output voltage
Voltage applied when the band output is
OFF
Band output current
Pin3
Pin4
Pin11
Not to exceed V
f
REF
output
CC1
V
BSOFF
14.4
V
I
BSON
Per 1 band output circuit
50mA per 1 band output circuit
3circuit are pn at same time
Ta=+75
°
C
50.0
mA
t
BSON
ON the time when the band output is ON
10
sec
P
T
T
d
Power dissipation
Operating temperature
Storage temperature
450 (470)
-20 to +75
-40 to +125
mW
°
C
°
C
opr
stg
Symbol
V
CC1
V
CC2
V
CC3
f
opr1
f
opr2
Parameter
Conditions
Ratings
4.5 to 5.5
V
CC1
to 13.2
28 to 35
4.0
80 to 1,300
Unit
V
V
V
MHz
MHz
Supply voltage 1
Supply voltage 2
Supply voltage 3
Operating frequency (1)
Operating frequency (2)
Pin3
Pin4
Pin11
Crystal oscillation circuit
I
BDL
Band output current 5 to 8
Normally 1 circuit is on. 2 circuits on at the
same time is max. It is prohibited to have
3 or more circuits turned on at the same time.
0 to 40
mA