參數資料
型號: M93S56-BN3TG
廠商: 意法半導體
元件分類: EEPROM
英文描述: 4Kbit, 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection
中文描述: 4Kbit,2Kbit和1Kbit 16位寬MICROWIRE串行EEPROM的訪問與街區保護
文件頁數: 11/34頁
文件大?。?/td> 525K
代理商: M93S56-BN3TG
11/34
M93S66, M93S56, M93S46
be started, and the addressed location will not be
programmed.
While the M93Sx6 is performing a write cycle, but
after a delay (t
SLSH
) before the status information
becomes available, Chip Select Input (S) can be
driven High to monitor the status of the write cycle:
Serial Data Output (Q) is driven Low while the
M93Sx6 is still busy, and High when the cycle is
complete, and the M93Sx6 is ready to receive a
new instruction. The M93Sx6 ignores any data on
the bus while it is busy on a write cycle. Once the
M93Sx6 is Ready, Serial Data Output (Q) is driven
High, and remains in this state until a new start bit
is decoded or the Chip Select Input (S) is brought
Low.
Programming is internally self-timed, so the exter-
nal Serial Clock (C) may be disconnected or left
running after the start of a write cycle.
Write All
The Write All Memory with same Data (WRAL) in-
struction is valid only after the Protection Register
has been cleared by executing a Protection Reg-
ister Clear (PRCLEAR) instruction. The Write All
Memory with same Data (WRAL) instruction simul-
taneously writes the whole memory with the same
data word given in the instruction.
Write Enable (W) must be held High before and
during the instruction. Input address and data, on
Serial Data Input (D) are sampled on the rising
edge of Serial Clock (C).
After the last data bit has been sampled,
the Chip
Select Input (S) must be taken Low before the next
rising edge of Serial Clock (C).
If Chip Select Input
(S) is brought Low before or after this specific time
frame, the self-timed programming cycle will not
be started, and the addressed location will not be
programmed.
While the M93Sx6 is performing a write cycle, but
after a delay (t
SLSH
) before the status information
becomes available, Chip Select Input (S) can be
driven High to monitor the status of the write cycle:
Serial Data Output (Q) is driven Low while the
M93Sx6 is still busy, and High when the cycle is
complete, and the M93Sx6 is ready to receive a
new instruction. The M93Sx6 ignores any data on
the bus while it is busy on a write cycle. Once the
M93Sx6 is Ready, Serial Data Output (Q) is driven
High, and remains in this state until a new start bit
is decoded or the Chip Select Input (S) is brought
Low.
Programming is internally self-timed, so the exter-
nal Serial Clock (C) may be disconnected or left
running after the start of a write cycle.
相關PDF資料
PDF描述
M93S56-BN3T 4Kbit, 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection
M93S56-BN3P Octal Transceivers And Line/Memory Drivers With 3-State Outputs 20-TSSOP -40 to 85
M95020-WMN3 4Kbit, 2Kbit and 1Kbit Serial SPI Bus EEPROM With High Speed Clock
M95020-RBN3 4Kbit, 2Kbit and 1Kbit Serial SPI Bus EEPROM With High Speed Clock
M95020-MN3T 4Kbit, 2Kbit and 1Kbit Serial SPI Bus EEPROM With High Speed Clock
相關代理商/技術參數
參數描述
M93S56-BN3TP 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4Kbit, 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection
M93S56-BN6 功能描述:電可擦除可編程只讀存儲器 RO 511-M93S56-WBN6 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M93S56-BN6G 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4Kbit, 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection
M93S56-BN6P 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4Kbit, 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection
M93S56-BN6T 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4Kbit, 2Kbit and 1Kbit 16-bit wide MICROWIRE Serial Access EEPROM with Block Protection