參數資料
型號: M95080-MN6T
廠商: 意法半導體
元件分類: EEPROM
英文描述: 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock
中文描述: 64/32/16/8千位串行SPI總線的EEPROM高速時鐘
文件頁數: 18/39頁
文件大?。?/td> 590K
代理商: M95080-MN6T
M95640, M95320
18/39
Figure 14. Byte Write (WRITE) Sequence
Note:
Depending on the memory size, as shown in Table 6, the most significant address bits are Don’t Care.
Write to Memory Array (WRITE)
As shown in Figure 14, to send this instruction to
the device, Chip Select (S) is first driven Low. The
bits of the instruction byte, address byte, and at
least one data byte are then shifted in, on Serial
Data Input (D).
The instruction is terminated by driving Chip Se-
lect (S) High at a byte boundary of the input data.
In the case of Figure 14, this occurs after the
eighth bit of the data byte has been latched in, in-
dicating that the instruction is being used to write
a single byte. The self-timed Write cycle starts,
and continues for a period t
WC
(as specified in Ta-
bles 18 to 22), at the end of which the Write in
Progress (WIP) bit is reset to 0.
If, though, Chip Select (S) continues to be driven
Low, as shown in Figure 15, the next byte of input
data is shifted in, so that more than a single byte,
starting from the given address towards the end of
the same page, can be written in a single internal
Write cycle.
Each time a new data byte is shifted in, the least
significant bits of the internal address counter are
incremented. If the number of data bytes sent to
the device exceeds the page boundary, the inter-
nal address counter rolls over to the beginning of
the page, and the previous data there are overwrit-
ten with the incoming data. (The page size of
these devices is 32 bytes).
The instruction is not accepted, and is not execut-
ed, under the following conditions:
– if the Write Enable Latch (WEL) bit has not been
set to 1 (by executing a Write Enable instruction
just before)
– if a Write cycle is already in progress
– if the device has not been deselected, by Chip
Select (S) being driven High, at a byte boundary
(after the eighth bit, b0, of the last data byte that
has been latched in)
– if the addressed page is in the region protected
by the Block Protect (BP1 and BP0) bits.
C
D
AI01795D
S
Q
15
2
1
3
4
5
6
7
8
9 10
20 21 22 23 24 25 26 27
14 13
3
2
1
0
28 29 30
High Impedance
Instruction
16-Bit Address
0
7
6
5
4
3
2
0
1
Data Byte
31
相關PDF資料
PDF描述
M95080-RBN3T 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock
M95080-RBN5T 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock
M95080-RBN6 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock
M95080-RBN6T 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock
M95080-RDL1T 64 x 36 x 2 bidirectional synchronous FIFO memory 132-BQFP 0 to 70
相關代理商/技術參數
參數描述
M95080-MN6TP 功能描述:電可擦除可編程只讀存儲器 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M95080-MN6TP/S 制造商:STMicroelectronics 功能描述:EEPROM SERL-SPI 8KBIT 1KX8 5V 8PIN SO N - Tape and Reel
M95080-RDW6TP 功能描述:電可擦除可編程只讀存儲器 16 Kbit and 8 Kbit Seril SPI bus 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M95080-RMB6TG 功能描述:電可擦除可編程只讀存儲器 16 Kbit and 8 Kbit RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M95080-RMC6TG 功能描述:電可擦除可編程只讀存儲器 8 Kbit SPI BUS EE 10MHz CR 5ms RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8