- 您現在的位置：買賣IC網 > PDF目錄359119 > M95080-WMN5T (意法半導體) 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock PDF資料下載
參數資料
| 型號： | M95080-WMN5T |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| 中文描述： | 64/32/16/8千位串行SPI總線的EEPROM高速時鐘 |
| 文件頁數： | 6/39頁 |
| 文件大小： | 590K |
| 代理商： | M95080-WMN5T |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
M95640, M95320
6/39
SIGNAL DESCRIPTION
During all operations, V
CC
must be held stable and
within the specified valid range: V
CC
(min) to
V
CC
(max).
All of the input and output signals must be held
High or Low (according to voltages of V
IH
, V
OH
, V
IL
or V
OL
, as specified in Tables 13 to 17). These sig-
nals are described next.
Serial Data Output (Q).
This output signal is
used to transfer data serially out of the device.
Data is shifted out on the falling edge of Serial
Clock (C).
Serial Data Input (D).
This input signal is used to
transfer data serially into the device. It receives in-
structions, addresses, and the data to be written.
Values are latched on the rising edge of Serial
Clock (C).
Serial Clock (C).
This input signal provides the
timing of the serial interface. Instructions, address-
es, or data present at Serial Data Input (D) are
latched on the rising edge of Serial Clock (C). Data
on Serial Data Output (Q) changes after the falling
edge of Serial Clock (C).
Chip Select (S).
When this input signal is High,
the device is deselected and Serial Data Output
(Q) is at high impedance. Unless an internal Write
cycle is in progress, the device will be in the Stand-
by mode. Driving Chip Select (S) Low enables the
device, placing it in the active power mode.
After Power-up, a falling edge on Chip Select (S)
is required prior to the start of any instruction.
Hold (HOLD).
The Hold (HOLD) signal is used to
pause any serial communications with the device
without deselecting the device.
During the Hold condition, the Serial Data Output
(Q) is high impedance, and Serial Data Input (D)
and Serial Clock (C) are Don’t Care.
To start the Hold condition, the device must be se-
lected, with Chip Select (S) driven Low.
Write Protect (W).
The main purpose of this in-
put signal is to freeze the size of the area of mem-
ory that is protected against Write instructions (as
specified by the values in the BP1 and BP0 bits of
the Status Register).
This pin must be driven either High or Low, and
must be stable during all write operations.
相關PDF資料 |
PDF描述 |
|---|---|
| M95080-WMN6 | 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95080-WMN6T | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95080BN | Octal Edge-Triggered D-Type Flip-Flops with 3-State Outputs 20-TSSOP -40 to 85 |
| M95080-WDW3 | 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95080-WMN3 | 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M95080-WMN6 | 功能描述:電可擦除可編程只讀存儲器 5.5V 8K (1Kx8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M95080-WMN6P | 功能描述:電可擦除可編程只讀存儲器 2.5 V to 5.5V EE RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M95080-WMN6T | 功能描述:電可擦除可編程只讀存儲器 5.5V 8K (1Kx8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M95080-WMN6TP | 功能描述:電可擦除可編程只讀存儲器 2.5 V to 5.5V 8K RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M95080-WMN6TP/S | 制造商:STMicroelectronics 功能描述:EEPROM SERL-SPI 8KBIT 1KX8 3.3V/5V 8PIN SO N - Tape and Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。