- 您現在的位置：買賣IC網 > PDF目錄359120 > M95160-BN6 (意法半導體) 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock PDF資料下載
參數資料
| 型號： | M95160-BN6 |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock |
| 中文描述： | 16Kbit和8Kbit SPI總線串行EEPROM的高速時鐘 |
| 文件頁數： | 9/40頁 |
| 文件大?。?/td> | 648K |
| 代理商： | M95160-BN6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
9/40
M95160, M95080
OPERATING FEATURES
Power-up
When the power supply is turned on, V
CC
rises
from V
SS
to V
CC
.
During this time, the Chip Select (S) must be al-
lowed to follow the V
CC
voltage. It must not be al-
lowed to float, but should be connected to V
CC
via
a suitable pull-up resistor.
As a built in safety feature, Chip Select (S) is edge
sensitive as well as level sensitive. After Power-
up, the device does not become selected until a
falling edge has first been detected on Chip Select
(S). This ensures that Chip Select (S) must have
been High, prior to going Low to start the first op-
eration.
Power On Reset: V
CC
Lock-Out Write Protect
In order to prevent data corruption and inadvertent
Write instructions during Power-up, a Power On
Reset (POR) circuit is included. The internal reset
is held active until V
CC
has reached the Power On
Reset (POR) threshold voltage, and all operations
are disabled – the device will not respond to any
instruction. In the same way, when V
CC
drops from
the operating voltage, below the Power On Reset
(POR) threshold voltage, all operations are dis-
abled and the device will not respond to any in-
struction.
A stable and valid V
CC
must be applied before ap-
plying any logic signal.
Power-down
At Power-down, the device must be deselected.
Chip Select (S) should be allowed to follow the
voltage applied on V
CC
.
Active Power and Standby Power Modes
When Chip Select (S) is Low, the device is select-
ed, and in the Active Power mode. The device
consumes I
CC
, as specified in
Table 14.
to
Table
18.
.
When Chip Select (S) is High, the device is dese-
lected. If an Erase/Write cycle is not currently in
progress, the device then goes in to the Standby
Power mode, and the device consumption drops
to I
CC1
.
Hold Condition
The Hold (HOLD) signal is used to pause any se-
rial communications with the device without reset-
ting the clocking sequence.
During the Hold condition, the Serial Data Output
(Q) is high impedance, and Serial Data Input (D)
and Serial Clock (C) are Don’t Care.
To enter the Hold condition, the device must be
selected, with Chip Select (S) Low.
Normally, the device is kept selected, for the whole
duration of the Hold condition. Deselecting the de-
vice while it is in the Hold condition, has the effect
of resetting the state of the device, and this mech-
anism can be used if it is required to reset any pro-
cesses that had been in progress.
The Hold condition starts when the Hold (HOLD)
signal is driven Low at the same time as Serial
Clock (C) already being Low.
The Hold condition ends when the Hold (HOLD)
signal is driven High at the same time as Serial
Clock (C) already being Low.
相關PDF資料 |
PDF描述 |
|---|---|
| M95160-BN6T | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95160-DL1T | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95160-DL3T | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95160-DL5T | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95160-DL6T | 64/32/16/8 Kbit Serial SPI Bus EEPROM With High Speed Clock |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M95160-BN6T | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16Kbit and 8Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95160-BPMN6 | 功能描述:電可擦除可編程只讀存儲器 5.5V 16K (2Kx8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| M95160-DF | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:16-Kbit serial SPI bus EEPROM with high-speed clock |
| M95160-DFDW6TP | 制造商:STMicroelectronics 功能描述:E-EPROM |
| M95160-DFMC6TG | 功能描述:IC EEPROM 16KB SPI BUS 8UFDFPN 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:16K（2K x 8） 速度:5MHz 接口:SPI 串行 電壓 - 電源:1.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C（TA） 封裝/外殼:8-UFDFN 裸露焊盤 供應商器件封裝:8-UFDFPN（2x3） 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。