- 您現在的位置：買賣IC網 > PDF目錄224185 > M95256-RDW3/A (STMICROELECTRONICS) 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 PDF資料下載
參數資料
| 型號： | M95256-RDW3/A |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | PROM |
| 英文描述： | 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| 封裝： | 0.169 INCH, TSSOP-8 |
| 文件頁數： | 14/43頁 |
| 文件大?。?/td> | 431K |
| 代理商： | M95256-RDW3/A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
M95256, M95256-W, M95256-R
Instructions
21/42
5.6
Write to Memory Array (WRITE)
As shown in Figure 10, to send this instruction to the device, Chip Select (S) is first driven
Low. The bits of the instruction byte, address byte, and at least one data byte are then
shifted in, on Serial Data Input (D).
The instruction is terminated by driving Chip Select (S) High at a byte boundary of the input
data. In the case of Figure 10, this occurs after the eighth bit of the data byte has been
latched in, indicating that the instruction is being used to write a single byte. The self-timed
the end of which the Write in Progress (WIP) bit is reset to 0.
If, though, Chip Select (S) continues to be driven Low, as shown in Figure 11, the next byte
of input data is shifted in, so that more than a single byte, starting from the given address
towards the end of the same page, can be written in a single internal Write cycle.
Each time a new data byte is shifted in, the least significant bits of the internal address
counter are incremented. If the number of data bytes sent to the device exceeds the page
boundary, the internal address counter rolls over to the beginning of the page, and the
previous data there are overwritten with the incoming data. (The page size of these devices
is 64 bytes).
The instruction is not accepted, and is not executed, under the following conditions:
●
if the Write Enable Latch (WEL) bit has not been set to 1 (by executing a Write Enable
instruction just before)
●
if a Write cycle is already in progress
●
if the device has not been deselected, by Chip Select (S) being driven High, at a byte
boundary (after the eighth bit, b0, of the last data byte that has been latched in)
●
if the addressed page is in the region protected by the Block Protect (BP1 and BP0)
bits.
Figure 10. Byte Write (WRITE) Sequence
1.
The most significant address bit (b15) is Don’t Care.
C
D
AI01795D
S
Q
15
2
1
3456789 10
20 21 22 23 24 25 26 27
14 13
3210
28 29 30
High Impedance
Instruction
16-Bit Address
0
765432
0
1
Data Byte
31
相關PDF資料 |
PDF描述 |
|---|---|
| M95256-RMN6P/A | 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M95256-WDW3T/A | 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| M95256-RDW6TG | 32K X 8 SPI BUS SERIAL EEPROM, PDSO8 |
| MA-306-29.4912M-K0 | QUARTZ CRYSTAL RESONATOR, 29.4912 MHz |
| MA04206 | 2-PORT SAW RESONATOR, 433.92 MHz |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M95256RDW3G | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit serial SPI bus EEPROM with high-speed clock |
| M95256-RDW3G | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256Kbit and 128Kbit Serial SPI Bus EEPROM With High Speed Clock |
| M95256-RDW3G/A | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit Serial SPI bus EEPROM with high speed clock |
| M95256-RDW3G/K | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit serial SPI bus EEPROM with high-speed clock |
| M95256-RDW3G/V | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit Serial SPI bus EEPROM with high speed clock |
發布緊急采購，3分鐘左右您將得到回復。