參數資料
型號： M95256-RDW6TG
廠商： STMICROELECTRONICS
元件分類： PROM
英文描述： 32K X 8 SPI BUS SERIAL EEPROM, PDSO8
封裝： 0.169 INCH, ROHS COMPLIANT, TSSOP-8
文件頁數： 3/44頁
文件大小： 386K
代理商： M95256-RDW6TG
M95256, M95256-W, M95256-R
Operating features
●
deselected (at next power-up, a falling edge is required on Chip Select (S) before any
instruction can be started).
●
not in the Hold condition
●
Status register:
–
the Write Enable Latch (WEL) is reset to 0
–
the Write In Progress (WIP) is reset to 0
–
the SRWD, BP1 and BP0 bits of the Status Register are non-volatile bits and
therefore remain unchanged)
Note:
When VCC passes the power on reset threshold voltage and until it reaches the minimum
VCC operating voltage, the memory must not be selected/accessed.
3.8.4
Power-down
During power-down (continuous decrease in VCC below the minimum VCC operating
voltage), the device must be:
●
deselected (Chip Select (S) should be allowed to follow the voltage applied on VCC)
●
in Standby Power mode (there should not be any internal Write cycle in progress).
4
Operating features
4.1
Hold condition
The Hold (HOLD) signal is used to pause any serial communications with the device without
resetting the clocking sequence.
During the Hold condition, the Serial Data output (Q) is high impedance, and Serial Data
input (D) and Serial Clock (C) are Don’t Care.
To enter the Hold condition, the device must be selected, with Chip Select (S) low.
Normally, the device is kept selected, for the whole duration of the Hold condition.
Deselecting the device while it is in the Hold condition, has the effect of resetting the state of
the device, and this mechanism can be used if it is required to reset any processes that had
been in progress.
The Hold condition starts when the Hold (HOLD) signal is driven low at the same time as
Serial Clock (C) already being low (as shown in Figure 5).
The Hold condition ends when the Hold (HOLD) signal is driven high at the same time as
Serial Clock (C) already being low.
Figure 5 also shows what happens if the rising and falling edges are not timed to coincide
with Serial Clock (C) being low.
相關PDF資料
PDF描述
MA-306-29.4912M-K0 QUARTZ CRYSTAL RESONATOR, 29.4912 MHz
MA04206 2-PORT SAW RESONATOR, 433.92 MHz
MA05199 1-PORT SAW RESONATOR, 434.42 MHz
MA1050 1 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, SIP7
MA21D35 1 A, 30 V, SILICON, SIGNAL DIODE
相關代理商/技術參數
參數描述
M95256-RDW6TG/A 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit Serial SPI bus EEPROM with high speed clock
M95256-RDW6TG/K 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit serial SPI bus EEPROM with high-speed clock
M95256-RDW6TG/V 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit Serial SPI bus EEPROM with high speed clock
M95256RDW6TP 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:256 Kbit serial SPI bus EEPROM with high-speed clock
M95256-RDW6TP 功能描述:電可擦除可編程只讀存儲器 256 Kbit Serial Bus 電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*