- 您現在的位置：買賣IC網 > PDF目錄296459 > MADP-017025-13140G SILICON, PIN DIODE PDF資料下載
參數資料
| 型號： | MADP-017025-13140G |
| 元件分類： | 參考電壓二極管 |
| 英文描述： | SILICON, PIN DIODE |
| 封裝： | ROHS COMPLIANT, CASE ODS-1314, 2 PIN |
| 文件頁數： | 4/4頁 |
| 文件大?。?/td> | 160K |
| 代理商： | MADP-017025-13140G |
North America Tel: 800.366.2266 / Fax: 978.366.2266
Europe Tel: 44.1908.574.200 / Fax: 44.1908.574.300
Asia/Pacific Tel: 81.44.844.8296 / Fax: 81.44.844.8298
Visit www.macom.com for additional data sheets and product information.
M/A-COM Inc. and its affiliates reserve the right to make changes to the product(s) or
information contained herein without notice.
SURMOUNT 25M PIN Diodes
RoHS Compliant
M/A-COM Products
Rev 3
MADP-017025-1314
MADP-030025-1314
ADVANCED:
Data Sheets contain information regarding a product M/A-COM is considering for
development. Performance is based on target specifications, simulated results, and/or prototype
measurements. Commitment to develop is not guaranteed.
PRELIMINARY:
Data Sheets contain information regarding a product M/A-COM has under develop-
ment. Performance is based on engineering tests. Specifications are typical. Mechanical outline has
been fixed. Engineering samples and/or test data may be available. Commitment to produce in
volume is not guaranteed.
Assembly Guidelines
Handling
All semiconductor chips should be handled with care to avoid damage or contamination from perspiration and skin
oils. The use of plastic tipped tweezers or vacuum pickups is strongly recommended for individual components.
Bulk handling should insure that abrasion and mechanical shock are minimized.
Bonding
Attachment to a circuit board is made simple through the use of surface mount technology. Mounting pads are
conveniently located on the bottom surface of these devices and are removed from the active junction locations.
These devices are well suited for solder or conductive epoxy attachment onto hard and soft substrates. The use
of 60/40, Pb/Sn,
80/20, Au/Sn or any other lead-free solder is recommended to achieve the lowest series
resistance and optimum heat sink.
When soldering these devices to a hard substrate, hot gas die bonding is preferred. We recommend utilizing a
vacuum tip and applying a force of 40 - 60 grams to the top surface of the device. When soldering, position the die
so that its mounting pads are aligned with the circuit board mounting pads and reflow the solder by heating the
circuit trace near the mounting pads while applying 40 to 60 grams of force perpendicular to the top surface of the
die. Both mounting pads should be heated simultaneously so that the solder under both pads flows at the same
time. The solder joint should not be made one at a time. By doing so, would create an un-equal heat flow and
potentially create thermal stress to the chip.
Solder reflow should not be performed by causing heat to flow through the top surface of the die. Die should be
uniformly heated in a re-flow oven. Proper flow is easily determined looking down from the top since the HMIC
glass is transparent and the edges of the mounting pads can be visually inspected through the die after
at-
tachment is complete. A typical soldering process profile and handling instructions are provided in
Appli-
cation Notes, M538 Surface Mounting Instructions and M541 Bonding and Handling Procedures on the MA-
COM website at www.macom.com/Application%20Notes/default.asp.
Conductive silver epoxy may also be used for die attachment, in lower Incident power applications where the
average power is < 1 W. Apply a thin controlled amount approximately 1- 2 mils thick to minimize ohmic and
thermal stresses. Take care not to bridge the gap between the chip pads with epoxy. A thin epoxy fillet should be
visible around the perimeter of the pads after placement to ensure full coverage. Cure per epoxy per
manufacturer’s recommended schedule.
Gel Pack
MADP-017025-13140G
MADP-030025-13140G
Ordering Information
相關PDF資料 |
PDF描述 |
|---|---|
| MADP00716101269 | SILICON, PIN DIODE |
| MADS-001317-1320AG | SILICON, mm WAVE BAND, MIXER DIODE |
| MAIA-007150-0001TR | RF/MICROWAVE MODULATOR |
| MAMXES0068 | 10 MHz - 2000 MHz RF/MICROWAVE DOUBLE BALANCED MIXER, 8.5 dB CONVERSION LOSS-MAX |
| MAN3G10 | 7 SEG NUMERIC DISPLAY, GREEN, 7.62 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MADP-017025-13140P | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:SURMOUNT? 25μM PIN Diodes RoHS Compliant |
| MADP-017025-1314G | 制造商:M/A-COM Technology Solutions 功能描述:SURMOUNT- 25?M PIN DIODES - Gel-pak, waffle pack, wafer, diced wafer on film |
| MADP-030015-1314 | 制造商:MA-COM 制造商全稱:M/A-COM Technology Solutions, Inc. 功能描述:SURMOUNT? 15μM PIN Diodes RoHS Compliant |
| MADP-030015-13140G | 功能描述:PIN 二極管 Ct=.78pF Rs=.49ohm IP3=-37.0dBc RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 反向電壓:200 V 正向連續電流: 頻率范圍:10 MHz to 6 GHz 端接類型:SMD/SMT 封裝 / 箱體:QFN-3 封裝:Reel |
| MADP-030015-13140P | 功能描述:PIN 二極管 1/6000MHz .78pF -55C +125C RoHS:否 制造商:Skyworks Solutions, Inc. 配置: 反向電壓:200 V 正向連續電流: 頻率范圍:10 MHz to 6 GHz 端接類型:SMD/SMT 封裝 / 箱體:QFN-3 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。