參數資料
型號: MAX1020BETX+T
廠商: Maxim Integrated Products
文件頁數: 29/44頁
文件大?。?/td> 0K
描述: IC ADC/DAC 10BIT 36-TQFN-EP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
類型: ADC,DAC
分辨率(位): 10 b
采樣率(每秒): 225k
數據接口: MICROWIRE?,QSPI?,串行,SPI?
電壓電源: 模擬和數字
電源電壓: 4.75 V ~ 5.25 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 36-WFQFN 裸露焊盤
供應商設備封裝: 36-TQFN 裸露焊盤(6x6)
包裝: 帶卷 (TR)
MAX1020/MAX1022/MAX1057/MAX1058
10-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
______________________________________________________________________________________
35
Do not issue a second
CNVST signal before EOC goes
low; otherwise, the FIFO can be corrupted. Wait until all
conversions are complete before reading the FIFO. SPI
communications to the DAC and GPIO registers are per-
mitted during conversion. However, coupled noise may
result in degraded ADC signal-to-noise ratio (SNR).
Externally Timed Acquisitions and
Internally Timed Conversions with
CNVST
ADC Conversions in Clock Mode 01
In clock mode 01, conversions are requested one at a
time using
CNVST and performed automatically using
the internal oscillator. See Figure 7 for clock mode 01
timing after a command byte is issued.
Setting
CNVST low begins an acquisition, wakes up the
ADC, and places it in track mode. Hold
CNVST low for
at least 1.4s to complete the acquisition. If reference
mode 00 or 10 is selected, an additional 45s is
required for the internal reference to power up. If a tem-
perature measurement is being requested, reference
power-up and temperature measurement is internally
timed. In this case, hold
CNVST low for at least 40s.
Set
CNVST high to begin a conversion. Sampling is
completed approximately 500ns after
CNVST goes
high. After the conversion is complete, the ADC shuts
down and pulls
EOC low. EOC stays low until CS or
CNVST is pulled low again. Wait until EOC goes low
before pulling
CS or CNVST low. The number of CNVST
signals must equal the number of conversions request-
ed by the scan and averaging registers to correctly
update the FIFO. Wait until all conversions are com-
plete before reading the FIFO. SPI communications to
the DAC and GPIO registers are permitted during con-
(UP TO 514 INTERNALLY CLOCKED ACQUISITIONS AND CONVERSIONS)
CS
DOUT
MSB1
tRDS
LSB1
MSB2
SCLK
X = DON'T CARE.
CNVST
EOC
Figure 6. Clock Mode 00—After writing a command byte, set
CNVST low for at least 40ns to begin a conversion.
(CONVERSION 2)
tCSW
tDOV
(ACQUISITION 2)
(ACQUISITION 1)
(CONVERSION 1)
CS
DOUT
MSB1
LSB1
MSB2
SCLK
CNVST
EOC
X = DON'T CARE.
Figure 7. Clock Mode 01—After writing a command byte, request multiple conversions by setting
CNVST low for each conversion.
相關PDF資料
PDF描述
MS3108E22-20S CONN PLUG 9POS RT ANG W/SCKT
MS27484T20F41PC CONN PLUG 41POS STRAIGHT W/PINS
MS27484T20F41PB CONN PLUG 41POS STRAIGHT W/PINS
MAX186DCWP+T IC ADC 12BIT SERIAL 20-SOIC
MS3450L20-16SZ CONN RCPT 9POS WALL MNT W/SCKT
相關代理商/技術參數
參數描述
MAX1021 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit, Multichannel ADCs/DACs with FIFO, Temperature Sensing, and GPIO Ports
MAX1021BETX 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1021BETX+ 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns/GPIO Ports RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1021BETX+T 功能描述:ADC / DAC多通道 10Bit AD/DACs w/FIFO Temp Sns/GPIO Ports RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1021BETX-T 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40