- 您現在的位置：買賣IC網 > PDF目錄2085 > MAX1028BCEP+ (Maxim Integrated Products)IC ADC 10-BIT 300KSPS 20-QSOP PDF資料下載
參數資料
| 型號： | MAX1028BCEP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 7/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10-BIT 300KSPS 20-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 位數： | 10 |
| 采樣率（每秒）： | 300k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 727mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 20-QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 12 個單端，單極；12 個單端，雙極；6 個差分，單極；6 個差分，雙極 |
| 產品目錄頁面： | 1395 (CN2011-ZH PDF) |
MAX1026/MAX1028/MAX1030
10-Bit 300ksps ADCs with FIFO,
Temp Sensor, Internal Reference
______________________________________________________________________________________
15
Power-Up Default State
The MAX1026/MAX1028/MAX1030 power up with all
blocks in shutdown, including the reference. All registers
power up in state 00000000, except for the setup regis-
ter, which powers up in clock mode 10 (CKSEL1 = 1).
Temperature Measurements
The MAX1026/MAX1028/MAX1030 perform tempera-
ture measurements with an internal diode-connected
transistor. The diode bias current changes from 68μA
to 4μA to produce a temperature-dependent bias volt-
age difference. The second conversion result at 4μA is
subtracted from the first at 68μA to calculate a digital
value that is proportional to absolute temperature. The
output data appearing at DOUT is the above digital
code minus an offset to adjust from Kelvin to Celsius.
The reference voltage used for the temperature mea-
surements is derived from the internal reference source
to ensure a resolution of 1/8 of a degree.
Output Data Format
Figures 4–7 illustrate the conversion timing for the
MAX1026/MAX1028/MAX1030. The 10-bit conversion
result is output in MSB-first format with 4 leading zeros
and 2 trailing sub-bits. The 12-bit temperature mea-
surement is output with 4 leading zeros. DIN data is
latched into the serial interface on the rising edge of
SCLK. Data on DOUT transitions on the falling edge of
SCLK. Conversions in clock modes 00 and 01 are initiat-
ed by
CNVST. Conversions in clock modes 10 and 11
are initiated by writing an input data byte to the conver-
sion register. Data is binary for unipolar mode and two’s
complement for bipolar mode.
BIT NAME
BIT
FUNCTION
UCH0/1
7 (MSB)
Set to 1 to configure AIN0 and AIN1 for unipolar differential conversion.
UCH2/3
6
Set to 1 to configure AIN2 and AIN3 for unipolar differential conversion.
UCH4/5
5
Set to 1 to configure AIN4 and AIN5 for unipolar differential conversion.
UCH6/7
4
Set to 1 to configure AIN6 and AIN7 for unipolar differential conversion.
UCH8/9
3
Set to 1 to configure AIN8 and AIN9 for unipolar differential conversion (MAX1028/MAX1030 only).
UCH10/11
2
Set to 1 to configure AIN10 and AIN11 for unipolar differential conversion (MAX1028/MAX1030 only).
UCH12/13
1
Set to 1 to configure AIN12 and AIN13 for unipolar differential conversion (MAX1030 only).
UCH14/15
0 (LSB)
Set to 1 to configure AIN14 and AIN15 for unipolar differential conversion (MAX1030 only).
Table 4. Unipolar Mode Register (Addressed Through Setup Register)
BIT NAME
BIT
FUNCTION
BCH0/1
7 (MSB)
Set to 1 to configure AIN0 and AIN1 for bipolar differential conversion.
BCH2/3
6
Set to 1 to configure AIN2 and AIN3 for bipolar differential conversion.
BCH4/5
5
Set to 1 to configure AIN4 and AIN5 for bipolar differential conversion.
BCH6/7
4
Set to 1 to configure AIN6 and AIN7 for bipolar differential conversion.
BCH8/9
3
Set to 1 to configure AIN8 and AIN9 for bipolar differential conversion (MAX1028/MAX1030 only).
BCH10/11
2
Set to 1 to configure AIN10 and AIN11 for bipolar differential conversion (MAX1028/MAX1030 only).
BCH12/13
1
Set to 1 to configure AIN12 and AIN13 for bipolar differential conversion (MAX1030 only).
BCH14/15
0 (LSB)
Set to 1 to configure AIN14 and AIN15 for bipolar differential conversion (MAX1030 only).
Table 5. Bipolar Mode Register (Addressed Through Setup Register)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1031BETI+T | IC ADC 10BIT 300KSPS 28-TQFN-EP |
| MAX1033EUP+ | IC ADC 14BIT SER 115KSPS 20TSSOP |
| MAX1035EUP+T | IC ADC 14BIT SER 115KSPS 20TSSOP |
| MAX1036LEKA+T | IC ADC 8BIT LP SERIAL SOT23-8 |
| MAX1060AEEI+ | IC ADC 10BIT 400KSPS 28-QSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1028BCEP+ | 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1028BCEP+T | 功能描述:模數轉換器 - ADC 10Bit 300ksps w/FIFO Temp Sensor Int Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1028BCEPT | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:10-Bit 300ksps ADCs with FIFO, Temp Sensor, Internal Reference |
| MAX1028BCEP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1028BEEP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。