- 您現在的位置：買賣IC網 > PDF目錄383308 > MAX1066AEUP (MAXIM INTEGRATED PRODUCTS INC) Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface PDF資料下載
參數資料
| 型號： | MAX1066AEUP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | ADC |
| 英文描述： | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
| 中文描述： | 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO20 |
| 封裝： | 4.40 MM, TSSOP-28 |
| 文件頁數： | 9/14頁 |
| 文件大?。?/td> | 335K |
| 代理商： | MAX1066AEUP |
During the acquisition, the analog input (AIN) charges
capacitor C
DAC
. The acquisition ends on the second
falling edge of
CS
. At this instant, the T/H switches
open. The retained charge on C
DAC
represents a
sample of the input.
In hold mode, the capacitive DAC adjusts during the
remainder of the conversion time to restore node ZERO
to zero within the limits of 14-bit resolution. At the end of
the conversion, force
CS
low to put valid data on the bus.
The time required for the T/H to acquire an input signal
is a function of how quickly its input capacitance is
charged. If the input signal
’
s source impedance is
high, the acquisition time lengthens and more time
must be allowed between conversions. The acquisition
time (t
ACQ
) is the maximum time the device takes to
acquire the signal. Use the following formula to calcu-
late acquisition time:
t
ACQ
= 11(R
S
+ R
IN
) x 35pF
where R
IN
= 800
, R
S
= the input signal
’
s source
impedance, and t
ACQ
is never less than 1.1μs. A
source impedance less than 1k
does not significantly
affect the ADC
’
s performance.
To improve the input-signal bandwidth under AC condi-
tions, drive AIN with a wideband buffer (>4MHz) that can
drive the ADC
’
s input capacitance and settle quickly.
Power-Down Modes
C
bit during the second falling edge of
CS
(see
Selecting
Standby or Shutdown Mode
section). The MAX1065/
MAX1066 automatically enter either standby mode, ref-
erence and buffer on, or shutdown, reference and
buffer off, after each conversion depending on the sta-
tus of R/
C
during the second falling edge of
CS
.
Internal Clock
The MAX1065/MAX1066 generate an internal conver-
sion clock. This frees the microprocessor from the bur-
den of running the SAR conversion clock. Total
conversion time after entering hold mode (second
falling edge of
CS
) to end-of-conversion (
EOC
) falling is
4.7μs (max).
Applications Information
Starting a Conversion
CS
and R/
C
control acquisition and conversion in the
MAX1065/MAX1066 (Figure 2). The first falling edge of
CS
powers up the device and puts it into acquisition
mode if R/
C
is low. The convert start is ignored if R/
C
is
high. When powering up from shutdown, the MAX1065/
MAX1066 needs at least 10ms (C
REFADJ
= 0.1μF, C
REF
= 1μF) for the internal reference to wake up and settle
before starting the conversion. The ADC may wake up
from shutdown to an unknown state. Put the ADC in a
known state by completing one
“
dummy
”
conversion.
The MAX1065/ MAX1066 will be in a known state, ready
for actual data acquisition, after the completion of the
dummy conversion. A dummy conversion consists of one
full conversion cycle.
The MAX1065 provides an alternative reset function to
reset the device (see
RESET
section).
Selecting Standby or Shutdown Mode
The MAX1065/MAX1066 have a selectable standby or
low-power shutdown mode. In standby mode, the
ADC
’
s internal reference and reference buffer do not
power down between conversions, eliminating the need
to wait for the reference to power up before performing
the next conversion. Shutdown mode powers down the
reference and reference buffer after completing a con-
version. Supply current is greatly reduced when in
shutdown mode. The reference and reference buffer
require a minimum of 10ms (C
REFADJ
= 0.1μF, C
REF
=
1μF) to power up and settle from shutdown.
The state of R/
C
at the second falling edge of
CS
selects which power-down mode the MAX1065/
MAX1066 enters upon conversion completion. Holding
R/
C
low causes the MAX1065/MAX1066 to enter stand-
by mode. The reference and buffer are left on after the
conversion completes. R/
C
high causes the
MAX1065/MAX1066 to enter shutdown mode and shut
down the reference and buffer after conversion
(Figures 5 and 6).
When using an external reference, set the REF power-
down bit high for lowest current operation.
M
Low-Power, 14-Bit Analog-to-Digital Converters
with Parallel Interface
_______________________________________________________________________________________
9
ANALOG INPUT
D0
–
D7 OR
D8
–
D13
EOC
REFADJ
DGND
REF
AGND
HBEN
CS
R/C
AIN
AV
DD
DV
DD
MAX1066
0.1
μ
F
0.1
μ
F
5V ANALOG
5V DIGITAL
0.1
μ
F
1
μ
F
μ
P DATA
BUS
HIGH
BYTE
LOW
BYTE
Figure 3. Typical Application Circuit for MAX1066
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1066BCUP | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1066BEUP | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1066CCUP | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX1066CEUP | Low-Power, 14-Bit Analog-to-Digital Converters with Parallel Interface |
| MAX107 | Dual, 6-Bit, 400Msps ADC with On-Chip, Wideband Input Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1066AEUP+ | 功能描述:模數轉換器 - ADC Low-Power 14-Bit w/Parallel Interface RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1066AEUP+T | 功能描述:模數轉換器 - ADC Low-Power 14-Bit w/Parallel Interface RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1066AEUP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1066BCUP | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1066BCUP+ | 功能描述:模數轉換器 - ADC Low-Power 14-Bit w/Parallel Interface RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。