- 您現在的位置：買賣IC網 > PDF目錄10485 > MAX1132BEAP+ (Maxim Integrated Products)IC ADC 16BIT 200KSPS 20-SSOP PDF資料下載
參數資料
| 型號： | MAX1132BEAP+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/19頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 16BIT 200KSPS 20-SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 66 |
| 位數： | 16 |
| 采樣率（每秒）： | 200k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 55mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 20-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，單極；1 個單端，雙極 |
| 產品目錄頁面： | 1395 (CN2011-ZH PDF) |
MAX1132/MAX1133
shutdown is long enough that the supply voltage or
ambient temperature may have changed.
Supplies, Layout, Grounding
and Bypassing
For best system performance, use separate analog and
digital ground planes. The two ground planes should
be tied together at the MAX1132/MAX1133. Use pins 3
and 14 as the primary AGND and DGND, respectively.
If the analog and digital supplies come from the same
source, isolate the digital supply from the analog with a
low value resistor (10).
The MAX1132/MAX1133 are not sensitive to the order
of AVDD and DVDD sequencing. Either supply can be
present in the absence of the other. Do not apply an
external reference voltage until after both AVDD and
DVDD are present.
Be sure that digital return currents do not pass through
the analog ground. All return current paths must be
low-impedance. A 5mA current flowing through a PC
board ground trace impedance of only 0.05 creates
an error voltage of about 250V, or about 2LSBs error
with a ±4V full-scale system. The board layout should
ensure as much as possible that digital and analog sig-
nal lines are kept separate. Do not run analog and digi-
tal lines parallel to one another. If you must cross one
with the other, do so at right angles.
The ADC is sensitive to high-frequency noise on the
AVDD power supply. Bypass this supply to the analog
ground plane with 0.1F. If the main supply is not ade-
quately bypassed, add an additional 1F or 10F low-
ESR capacitor in parallel with the primary bypass
capacitor.
Transfer Function
Figures 10 and 11 show the MAX1132/MAX1133’s
transfer functions. In unipolar mode, the output data is
binary format and in bipolar mode it is two’s comple-
ment.
Definitions
Integral Nonlinearity
Integral nonlinearity (INL) is the deviation of the values
on an actual transfer function from a straight line. This
straight line can be either a best-straight-line fit or a line
drawn between the end points of the transfer function,
once offset and gain errors have been nullified. INL for
the MAX1132/MAX1133 is measured using the end-
point method.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between
an actual step-width and the ideal value of 1LSB. A
DNL error specification of less than 1LSB guarantees
no missing codes and a monotonic transfer function.
Aperture Jitter
Aperture jitter (tAJ) is the sample-to-sample variation in
the time between the samples.
Aperture Delay
Aperture delay (tAD) is the time between the falling
edge of the sampling clock and the instant when an
actual sample is taken.
Signal-to-Noise Ratio
For a waveform perfectly reconstructed from digital sam-
ples, signal-to-noise ratio (SNR) is the ratio of full-scale
analog input (RMS value) to the RMS quantization error
(residual error). The ideal, theoretical, minimum analog-
to-digital noise is caused by quantization error only and
results directly from the ADCs resolution (N bits):
SNR = (6.02 N + 1.76)dB
In reality, there are other noise sources besides quanti-
zation noise, including thermal noise, reference noise,
clock jitter, etc. Therefore, SNR is calculated by taking
the ratio of the RMS signal to the RMS noise, which
includes all spectral components minus the fundamen-
tal, the first five harmonics, and the DC offset.
Signal-to-Noise Plus Distortion
Signal-to-Noise Plus Distortion (SINAD) is the ratio of
the fundamental input frequency’s RMS amplitude to
the RMS equivalent of all other ADC output signals:
SINAD (dB) = 20 log (SignalRMS/NoiseRMS)
Effective Number of Bits
Effective number of bits (ENOB) indicates the global
accuracy of an ADC at a specific input frequency and
sampling rate. An ideal ADCs error consists of quanti-
zation noise only. With an input range equal to the full-
scale range of the ADC, calculate the effective number
of bits as follows:
ENOB = (SINAD - 1.76) / 6.02
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the RMS
sum of the first five harmonics of the input signal to the
fundamental itself. This is expressed as:
THD=
×
+++
20
2
3
2
4
2
5
2
1
log
/
VVVV
V
16-Bit ADC, 200ksps, 5V Single-Supply
with Reference
16
______________________________________________________________________________________
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BTV-IV-F2 | CONVERTER MOD DC/DC 5.8V 150W |
| VE-BT0-IV-F4 | CONVERTER MOD DC/DC 5V 150W |
| MAX195BCPE+ | IC ADC 16BIT 85KSPS SHTDN 16-DIP |
| MS3106E12S-3SX | CONN PLUG 2POS STRAIGHT W/SCKT |
| MAX170CEWE+ | IC ADC 12BIT SERIAL 16-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1132BEAP+ | 功能描述:模數轉換器 - ADC 16-Bit 200ksps 5V Single-Supply w/Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1132BEAP+T | 功能描述:模數轉換器 - ADC 16-Bit 200ksps 5V Single-Supply w/Ref RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1132BEAP-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1132EVC16 | 功能描述:數據轉換 IC 開發工具 16-Bit 200ksps 5V Single-Supply w/Ref RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| MAX1132EVKIT | 功能描述:數據轉換 IC 開發工具 MAX1132 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。