- 您現在的位置：買賣IC網 > PDF目錄2008 > MAX11645EUA+T (Maxim Integrated Products)IC ADC 12BIT I2C/SRL 1CH 8UMAX PDF資料下載
參數資料
| 型號： | MAX11645EUA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT I2C/SRL 1CH 8UMAX |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 94.4k |
| 數據接口： | I²C，串行 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 362mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，單極；2 個單端，雙極；1 個差分，單極；1 個差分，雙極 |
MAX11644/MAX11645
Low-Power, 1-/2-Channel, I2C, 12-Bit ADCs
in Ultra-Tiny 1.9mm x 2.2mm Package
16
______________________________________________________________________________________
Data Byte (Read Cycle)
A read cycle must be initiated to obtain conversion
results. Read cycles begin with the bus master issuing a
START condition followed by seven address bits and a
read bit (R/W = 1). If the address byte is successfully
received, the MAX11644/MAX11645 (slave) issues an
acknowledge. The master then reads from the slave.
The result is transmitted in 2 bytes; first 4 bits of the first
byte are high, then MSB through LSB are consecutively
clocked out. After the master has received the byte(s), it
can issue an acknowledge if it wants to continue read-
ing or a not-acknowledge if it no longer wishes to read.
If the MAX11644/MAX11645 receive a not-acknowl-
edge, they release SDA, allowing the master to generate
a STOP or a repeated START condition. See the
Clock
Modes and Scan Mode sections for detailed information
on how data is obtained and converted.
Clock Modes
The clock mode determines the conversion clock and
the data acquisition and conversion time. The clock
mode also affects the scan mode. The state of the set-
up byte’s CLK bit determines the clock mode (Table 1).
At power-up, the MAX11644/MAX11645 are defaulted
to internal clock mode (CLK = 0).
Internal Clock
When configured for internal clock mode (CLK = 0), the
MAX11644/MAX11645 use their internal oscillator as
the conversion clock. In internal clock mode, the
MAX11644/MAX11645 begin tracking the analog input
after a valid address on the eighth rising edge of the
clock. On the falling edge of the ninth clock, the analog
signal is acquired and the conversion begins. While
converting the analog input signal, the MAX11644/
MAX11645 hold SCL low (clock stretching). After the
conversion completes, the results are stored in internal
memory. If the scan mode is set for multiple conver-
sions, they all happen in succession with each addi-
tional result stored in memory. The MAX11644/
MAX11645 contain two 12-bit blocks of memory. Once
all conversions are complete, the MAX11644/
MAX11645 release SCL, allowing it to be pulled high.
The master can now clock the results out of the memo-
ry in the same order the scan conversion has been
done at a clock rate of up to 1.7MHz. SCL is stretched
for a maximum of 8.3μs per channel (see Figure 10).
The device memory contains all of the conversion
results when the MAX11644/MAX11645 release SCL.
The converted results are read back in a first-in-first-out
(FIFO) sequence. The memory contents can be read
continuously. If reading continues past the result stored
in memory, the pointer wraps around and points to the
first result. Note that only the current conversion results
are read from memory. The device must be addressed
with a read command to obtain new conversion results.
The internal clock mode’s clock stretching quiets the
SCL bus signal, reducing the system noise during con-
version. Using the internal clock also frees the bus
master (typically a microcontroller) from the burden of
running the conversion clock, allowing it to perform
other tasks that do not need to use the bus.
CLOCK STRETCH
B) SCAN MODE CONVERSIONS WITH INTERNAL CLOCK
S
1
SLAVE ADDRESS
A
71 1
R
CLOCK STRETCH
NUMBER OF BITS
P OR Sr
1
8
RESULT 8 LSBs
8
RESULT 4 MSBs
A
1
A) SINGLE CONVERSION WITH INTERNAL CLOCK
S
1
SLAVE ADDRESS
71 1
R
NUMBER OF BITS
P OR Sr
1
8
RESULT 1 ( 4MSBs)
A
1
A
8
RESULT 1 (8 LSBs) A
8
RESULT N (8LSBs)
A
1
8
RESULT N (4MSBs)
SLAVE TO MASTER
MASTER TO SLAVE
CLOCK STRETCH
tACQ1
tCONV2
tACQ2
tCONVN
tACQN
tCONV
tACQ
1
tCONV1
Figure 10. Internal Clock Mode Read Cycles
相關PDF資料 |
PDF描述 |
|---|---|
| MAX11647EUA+T | IC ADC 10BIT I2C 94.4KSPS 8UMAX |
| MAX1166BEUP+ | IC ADC 16BIT 165KSPS 20-TSSOP |
| MAX1168BCEG+ | IC ADC 16BIT 200KSPS 24-QSOP |
| MAX1183ECM+TD | IC ADC 10BIT 40MSPS DL 48-TQFP |
| MAX1184ECM+TD | IC ADC 10BIT 20MSPS DL 48-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX11645EWC+ | 制造商:Maxim Integrated Products 功能描述: |
| MAX11645EWC+T | 功能描述:模數轉換器 - ADC 12-Bit 2Ch 94.4ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11646 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:2.7V to 3.6V and 4.5V to 5.5V, Low-Power, 1-/2-Channel, 2-Wire Serial, 10-Bit ADCs |
| MAX11646EUA+ | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 94.4ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX11646EUA+T | 功能描述:模數轉換器 - ADC 10-Bit 2Ch 94.4ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。