參數資料
型號: MAX1220BETX+T
廠商: Maxim Integrated Products
文件頁數: 29/43頁
文件大小: 0K
描述: IC ADC/DAC 12BIT 36-TQFN
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 2,500
類型: ADC,DAC
分辨率(位): 12 b
采樣率(每秒): 225k
數據接口: 串行
電壓電源: 模擬和數字
電源電壓: 4.75 V ~ 5.25 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 36-WFQFN 裸露焊盤
供應商設備封裝: 36-TQFN 裸露焊盤(6x6)
包裝: 帶卷 (TR)
MAX1220/MAX1257/MAX1258
12-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
______________________________________________________________________________________
35
scan is complete, EOC is pulled low and the results are
available in the FIFO. Wait until EOC goes low before
pulling CS low to communicate with the serial interface.
EOC stays low until CS or CNVST is pulled low again. A
temperature-conversion result, if requested, precedes
all other FIFO results.
Do not issue a second CNVST signal before EOC goes
low; otherwise, the FIFO can be corrupted. Wait until all
conversions are complete before reading the FIFO. SPI
communications to the DAC and GPIO registers are per-
mitted during conversion. However, coupled noise may
result in degraded ADC signal-to-noise ratio (SNR).
Externally Timed Acquisitions and
Internally Timed Conversions with
CNVST
ADC Conversions in Clock Mode 01
In clock mode 01, conversions are requested one at a
time using CNVST and performed automatically using
the internal oscillator. See Figure 7 for clock mode 01
timing after a command byte is issued.
Setting CNVST low begins an acquisition, wakes up the
ADC, and places it in track mode. Hold CNVST low for
at least 1.4s to complete the acquisition. If reference
mode 00 or 10 is selected, an additional 45s is
required for the internal reference to power up. If a tem-
perature measurement is being requested, reference
power-up and temperature measurement is internally
timed. In this case, hold CNVST low for at least 40ns.
(UP TO 514 INTERNALLY CLOCKED ACQUISITIONS AND CONVERSIONS)
CS
DOUT
MSB1
tRDS
LSB1
MSB2
SCLK
CNVST
EOC
Figure 6. Clock Mode 00—After writing a command byte, set CNVST low for at least 40ns to begin a conversion.
(CONVERSION 2)
tCSW
tDOV
(ACQUISITION 2)
(ACQUISITION 1)
(CONVERSION 1)
CS
DOUT
MSB1
LSB1
MSB2
SCLK
CNVST
EOC
Figure 7. Clock Mode 01—After writing a command byte, request multiple conversions by setting CNVST low for each conversion.
相關PDF資料
PDF描述
MS3114P16-26SW CONN RCPT 26POS JAM NUT W/SCKT
MAX188CCWP+ IC ADC 12BIT SERIAL 20-SOIC
74HC238N,652 IC DECODER/DEMUX 3-8LINE 16DIP
VE-B4L-IU-F2 CONVERTER MOD DC/DC 28V 200W
VE-B4L-IU-F1 CONVERTER MOD DC/DC 28V 200W
相關代理商/技術參數
參數描述
MAX1221BETX 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1221BETX+ 功能描述:ADC / DAC多通道 12-Bit 8Ch 300ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1221BETX+T 功能描述:ADC / DAC多通道 12-Bit 8Ch 300ksps 5.25V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1221BETX-T 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40
MAX1223BETX 制造商:Maxim Integrated Products 功能描述:12-BIT MULTICHANNEL ADC/DAC WITH F - Rail/Tube