- 您現在的位置：買賣IC網 > PDF目錄9751 > MAX1225CTC+ (Maxim Integrated Products)IC ADC 12BIT 1.5MSPS 12-TQFN PDF資料下載
參數資料
| 型號： | MAX1225CTC+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 1.5MSPS 12-TQFN |
| 標準包裝： | 75 |
| 位數： | 12 |
| 采樣率（每秒）： | 1.5M |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 18mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 12-WQFN 裸露焊盤 |
| 供應商設備封裝： | 12-TQFN-EP（4x4） |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個差分，雙極 |
Partial Power-Down and
Full Power-Down Modes
Power consumption can be reduced significantly by plac-
ing the MAX1224/MAX1225 in either partial power-down
mode or full power-down mode. Partial power-down
mode is ideal for infrequent data sampling and fast wake-
up time applications. Pull CNVST high after the 3rd SCLK
rising edge and before the 14th SCLK rising edge to
enter and stay in partial power-down mode (see Figure
6). This reduces the supply current to 1mA. Drive CNVST
low and allow at least 14 SCLK cycles to elapse before
driving CNVST high to exit partial power-down mode.
Full power-down mode is ideal for infrequent data sam-
pling and very low supply-current applications. The
MAX1224/MAX1225 have to be in partial power-down
mode in order to enter full power-down mode. Perform
the SCLK/CNVST sequence described above to enter
partial power-down mode. Then repeat the same
sequence to enter full power-down mode (see Figure
7). Drive CNVST low, and allow at least 14 SCLK cycles
to elapse before driving CNVST high to exit full power-
down mode. In partial/full power-down mode, maintain
a logic low or a logic high on SCLK to minimize power
consumption.
Transfer Function
Figure 8 shows the unipolar transfer function for the
MAX1224. Figure 9 shows the bipolar transfer function for
the MAX1225. The MAX1224 output is straight binary,
while the MAX1225 output is two’s complement.
Applications Information
External Reference
An external reference is required for the MAX1224/
MAX1225. Use a 4.7F and 0.01F bypass capacitor on
the REF pin for best performance. The reference input
structure allows a voltage range of +1V to VDD.
How to Start a Conversion
An analog-to-digital conversion is initiated by CNVST and
clocked by SCLK, and the resulting data is clocked out
on DOUT by SCLK. With SCLK idling high or low, a falling
edge on CNVST begins a conversion. This causes the
analog input stage to transition from track to hold mode,
and for DOUT to transition from high impedance to being
actively driven low. A total of 16 SCLK cycles are required
to complete a normal conversion. If CNVST is low during
the 16th falling SCLK edge, DOUT returns to high imped-
ance on the next rising edge of CNVST or SCLK,
enabling the serial interface to be shared by multiple
devices. If CNVST returns high after the 14th, but before
the 16th SCLK rising edge, DOUT remains active so con-
tinuous conversions can be sustained. The highest
throughput is achieved when performing continuous con-
versions. Figure 10 illustrates a conversion using a typical
serial interface.
MAX1224/MAX1225
1.5Msps, Single-Supply, Low-Power,
True-Differential, 12-Bit ADCs
______________________________________________________________________________________
11
Figure 7. SPI Interface—Full Power-Down Mode
1ST SCLK RISING EDGE
0
D11
D10
D9
D8
D7
DOUT
MODE
SCLK
CNVST
0
000
0
FPD
RECOVERY
PPD
NORMAL
0
DOUT ENTERS TRI-STATE ONCE CNVST GOES HIGH
EXECUTE PARTIAL POWER-DOWN TWICE
FIRST 8-BIT TRANSFER
SECOND 8-BIT TRANSFER
相關PDF資料 |
PDF描述 |
|---|---|
| MS27473T14A35SB | CONN PLUG 37POS STRAIGHT W/SCKT |
| MAX1079CTC+ | IC ADC 10BIT 1.5MSPS 12-TQFN |
| MAX9967ADCCQ+TD | IC DCL DUAL 500MBPS ATE 100TQFP |
| MS27497E24F29P | CONN RCPT 29POS WALL MNT W/PINS |
| D38999/26FJ43PN | CONN PLUG 43POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1225CTC+ | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1225CTC+T | 功能描述:模數轉換器 - ADC Integrated Circuits (ICs) RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1225CTC-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1225ETC | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1225ETC+ | 功能描述:模數轉換器 - ADC 12-Bit 1.5Msps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發(fā)布緊急采購，3分鐘左右您將得到回復。