- 您現在的位置：買賣IC網 > PDF目錄9499 > MAX1258BETM+ (Maxim Integrated Products)IC ADC/DAC 12BIT 48-TQFN PDF資料下載
參數資料
| 型號： | MAX1258BETM+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 14/43頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC/DAC 12BIT 48-TQFN |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 43 |
| 類型： | ADC，DAC |
| 分辨率（位）： | 12 b |
| 采樣率（每秒）： | 225k |
| 數據接口： | 串行 |
| 電壓電源： | 模擬和數字 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-TQFN-EP（7x7） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁
MAX1220/MAX1257/MAX1258
12-Bit, Multichannel ADCs/DACs with FIFO,
Temperature Sensing, and GPIO Ports
______________________________________________________________________________________
21
See Tables 5–8 for more details on configuring the
inputs. For the inputs that are configurable as CNVST,
REF2, and an analog input, only one function can be
used at a time.
Unipolar or Bipolar Conversions
Address the unipolar- and bipolar-mode registers
through the setup register (bits 1 and 0). See Table 5 for
the setup register. See Figures 3 and 4 for the transfer-
function graphs. Program a pair of analog inputs for dif-
ferential operation by writing a one to the appropriate bit
of the bipolar- or unipolar-mode register. Unipolar mode
sets the differential input range from 0 to VREF1. A nega-
tive differential analog input in unipolar mode causes the
digital output code to be zero. Selecting bipolar mode
sets the differential input range to ±VREF1 / 2. The digital
output code is binary in unipolar mode and two’s com-
plement in bipolar mode.
In single-ended mode, the MAX1220/MAX1257/
MAX1258 always operate in unipolar mode. The analog
inputs are internally referenced to AGND with a full-scale
input range from 0 to the selected reference voltage.
Analog Input (T/H)
The equivalent circuit of Figure 2 shows the ADC input
architecture of the MAX1220/MAX1257/MAX1258. In
track mode, a positive input capacitor is connected to
AIN0–AIN15 in single-ended mode and AIN0, AIN2,
and AIN4–AIN14 (only positive inputs) in differential
mode. A negative input capacitor is connected to
AGND in single-ended mode or AIN1, AIN3, and
AIN5–AIN15 (only negative inputs) in differential mode.
For external T/H timing, use clock mode 01. After the
T/H enters hold mode, the difference between the sam-
pled positive and negative input voltages is converted.
The input capacitance charging rate determines the
time required for the T/H to acquire an input signal. If
the input signal’s source impedance is high, the
required acquisition time lengthens.
Any source impedance below 300
does not signifi-
cantly affect the ADC’s AC performance. A high-imped-
ance source can be accommodated either by
lengthening tACQ (only in clock mode 01) or by placing
a 1F capacitor between the positive and negative ana-
log inputs. The combination of the analog-input source
impedance and the capacitance at the analog input cre-
ates an RC filter that limits the analog input bandwidth.
Input Bandwidth
The ADC’s input-tracking circuitry has a 1MHz small-
signal bandwidth, making it possible to digitize high-
speed transient events and measure periodic signals
with bandwidths exceeding the ADC’s sampling rate by
using undersampling techniques. Anti-alias prefiltering
of the input signals is necessary to avoid high-frequen-
cy signals aliasing into the frequency band
of interest.
Analog Input Protection
Internal electrostatic-discharge (ESD) protection diodes
clamp all analog inputs to AVDD and AGND, allowing
the inputs to swing from (AGND - 0.3V) to (AVDD +
0.3V) without damage. However, for accurate conver-
sions near full scale, the inputs must not exceed AVDD
by more than 50mV or be lower than AGND by 50mV. If
an analog input voltage exceeds the supplies, limit the
input current to 2mA.
Internal FIFO
The MAX1220/MAX1257/MAX1258 contain a first-
in/first-out (FIFO) buffer that holds up to 16 ADC results
plus one temperature result. The internal FIFO allows
the ADC to process and store multiple internally
clocked conversions and a temperature measurement
without being serviced by the serial bus.
If the FIFO is filled and further conversions are request-
ed without reading from the FIFO, the oldest ADC
results are overwritten by the new ADC results. Each
result contains 2 bytes, with the MSB preceded by four
leading zeros. After each falling edge of CS, the oldest
available pair of bytes of data is available at DOUT,
MSB first. When the FIFO is empty, DOUT is zero.
AIN0–AIN15
(SINGLE-ENDED),
AIN0, AIN2,
AIN4–AIN14
(DIFFERENTIAL)
COMPARATOR
HOLD
ACQ
HOLD
ACQ
HOLD
AVDD / 2
REF1
AGND
CIN+
CIN-
DAC
AGND
(SINGLE-ENDED),
AIN1, AIN3,
AIN5–AIN15
(DIFFERENTIAL)
Figure 2. Equivalent Input Circuit
相關PDF資料 |
PDF描述 |
|---|---|
| V110A48M300BF2 | CONVERTER MOD DC/DC 48V 300W |
| MAX1220BETX+ | IC ADC/DAC 12BIT 36-TQFN |
| MAX1221BETX+ | IC ADC/DAC 12BIT W/FIFO 36TQFNEP |
| MAX188DCWP+ | IC DAS 8CH 12BIT T/H LP 20-SOIC |
| MAX1407CAI+ | IC DAS 16BIT LP 28-SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1258BETM+ | 功能描述:ADC / DAC多通道 12-Bit 16Ch 300ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1258BETM+T | 功能描述:ADC / DAC多通道 12-Bit 16Ch 300ksps 5.5V Precision ADC RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1258BETM-T | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1258EVC16 | 功能描述:ADC / DAC多通道 Evaluation Kit/Evaluation System for the MAX1057 MAX1058 MAX1257 MAX1258 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
| MAX1258EVKIT | 功能描述:數據轉換 IC 開發工具 Evaluation Kit/Evaluation System for the MAX1057 MAX1058 MAX1257 MAX1258 RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。