- 您現在的位置：買賣IC網 > PDF目錄9864 > MAX1291ACEI+ (Maxim Integrated Products)IC ADC 12BIT 250KSPS 28-QSOP PDF資料下載
參數資料
| 型號： | MAX1291ACEI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 250KSPS 28-QSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 50 |
| 位數： | 12 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 667mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 28-QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 8 個單端，單極；8 個單端，雙極；4 個偽差分，單極；4 個偽差分，雙極 |
MAX1291/MAX1293
250ksps, +3V, 8-/4-Channel, 12-Bit ADCs
with +2.5V Reference and Parallel Interface
______________________________________________________________________________________
13
Selecting Clock Mode
The MAX1291/MAX1293 operate with either an internal
or an external clock. Control bits D6 and D7 select
either internal or external clock mode. The parts retain
the last requested clock mode if a power-down mode is
selected in the current input word. For both internal and
external clock mode, internal or external acquisition
can be used. At power-up, the MAX1291/MAX1293
enter the default external clock mode.
Internal Clock Mode
Select internal clock mode to release the P from the
burden of running the SAR conversion clock. To select
this mode, bit D7 of the control byte must be set to 1
and bit D6 must be set to 0. The internal clock frequen-
cy is then selected, resulting in a conversion time of
3.6s. When using the internal clock mode, tie the CLK
pin either high or low to prevent the pin from floating.
External Clock Mode
To select the external clock mode, bits D6 and D7 of
the control byte must be set to 1. Figure 6 shows the
clock and WR timing relationship for internal (Figure 6a)
and external (Figure 6b) acquisition modes with an
external clock. For proper operation, a 100kHz to
4.8MHz clock frequency with 30% to 70% duty cycle is
recommended. Operating the MAX1291/MAX1293 with
clock frequencies lower than 100kHz is not recom-
mended, because it causes a voltage droop across the
hold capacitor in the T/H stage that results in degraded
performance.
Digital Interface
Input (control byte) and output data are multiplexed on
a three-state parallel interface. This parallel interface
(I/O) can easily be interfaced with standard Ps. The
signals CS, WR, and RD control the write and read
operations. CS represents the chip select signal, which
enables a P to address the MAX1291/MAX1293 as an
I/O port. When high, CS disables the CLK WR and RD
inputs and forces the interface into a high-impedance
(high-Z) state.
Input Format
The control byte is latched into the device on pins
D7–D0 during a write command. Table 2 shows the
control byte format.
Output Format
The output format for both the MAX1291/MAX1293 is
binary in unipolar mode and two’s complement in bipo-
lar mode. When reading the output data, CS and RD
must be low. When HBEN = 0, the lower 8 bits are
read. With HBEN = 1, the upper 4 bits are available
and the output data bits D7–D4 are set either low in
unipolar mode or set to the value of the MSB in bipolar
mode (Table 5).
WR
CLK
WR
WR GOES HIGH WHEN CLK IS HIGH.
WR GOES HIGH WHEN CLK IS LOW.
tCWS
tCH
tCL
tCP
tCWH
ACQUISITION STARTS
CONVERSION STARTS
ACQUISITION ENDS
ACQMOD = "0"
Figure 6a. External Clock and WR Timing (Internal Acquisition Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1261ACEI+ | IC ADC 12BIT 250KSPS 28-QSOP |
| MS27484E16A26PA | CONN PLUG 26POS STRAIGHT W/PINS |
| MAX1262ACEI+ | IC ADC 12BIT 400KSPS 28-QSOP |
| VE-JNL-MX-F1 | CONVERTER MOD DC/DC 28V 75W |
| DP83848YBX/NOPB | IC TXRX ETHERNET PHYTERA 48-LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1291ACEI+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 250ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1291ACEI+T | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 250ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1291ACEI-T | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1291AEEI | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1291AEEI+ | 功能描述:模數轉換器 - ADC 12-Bit 8Ch 250ksps 3.6V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。