- 您現在的位置：買賣IC網 > PDF目錄10516 > MAX13020ASA+ (Maxim Integrated Products)IC TRANSCEIVER LIN 8-SOIC PDF資料下載
參數資料
| 型號： | MAX13020ASA+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 3/16頁 |
| 文件大小： | 0K |
| 描述： | IC TRANSCEIVER LIN 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 100 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | LIN |
| 電源電壓： | 5 V ~ 38 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
| 產品目錄頁面： | 1408 (CN2011-ZH PDF) |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
MAX13020/MAX13021
±60V Fault-Protected LIN Transceivers
11
Maxim Integrated
Low Slope Mode
Low slope mode is identical to normal slope mode, with
the exception of the LIN transmitter. In low slope mode,
the transmitter slew-rate is further limited for improved
EME performance. Maximum data rate is limited to
10.4kbaud due to the increased slew-rate limiting of the
LIN transmitter. From standby or sleep mode, drive
TXD logic-low, then drive NSLP logic-high for longer
than tGOTONORM to enter low slope mode. Drive NSLP
logic-low for longer than tGOTOSLEEP to force the
device into sleep mode from low slope mode.
LIN Bus Dominant Management
(MAX13021)
The MAX13021 provides two additional states to imple-
ment reduced current consumption during a LIN-to-
GND short condition. When the MAX13021 detects a
dominant-clamped fault on LIN, the device disables the
transmitter and enters a low-power fail-safe mode. The
receiver is disabled and a low-power comparator is
enabled to monitor the LIN bus. When a recessive state
is detected on LIN, the device exits fault mode and
returns to standby mode.
Fault Mode (MAX13021)
The device enters fault mode from normal slope or low
slope mode when a dominant state is detected on LIN
for longer than tLIN(DOM)(DET). In fault mode, the slave
termination resistor from LIN to BAT is disconnected,
and the LIN transmitter and receiver are disabled to
reduce power consumption. INH output remains pulled
high. A low-power comparator is enabled to monitor the
LIN bus. Fault mode is cleared, and the MAX13021
enters standby mode when a recessive state is detect-
ed on LIN for longer than tLIN(DOM)(REC).
Disable Mode (MAX13021)
The MAX13021 enters disable mode from fault mode
after NSLP is driven logic-low for longer than
tGOTOSLEEP. The INH output is high impedance in dis-
able mode to reduce current consumption. The LIN
transmitter and receiver are disabled, and the slave ter-
mination resistor from LIN to BAT is disconnected. A
low-power comparator is enabled to monitor the LIN
bus. The MAX13021 enters fault mode when NSLP is
driven logic-high for longer than tGOTONORM. The
device enters sleep mode if a recessive state is detect-
ed on LIN for longer than tLIN(DOM)(REC).
Local and Remote Wake-Up Events
The MAX13020/MAX13021 recognize local and remote
wake-up events from sleep mode. The MAX13021 also
recognizes local wake-up events from disable mode. A
local wake-up event is detected when NWAKE is held
at logic-low for longer than tGOTONORM after a falling
edge. NWAKE is internally pulled up to BAT with a
MODE
NSLP
TXD
PULLDOWN
RXD
INH
TRANSMITTER
RECEIVER
COMMENTS
SLEEP
0
330k
High-Z
Disabled
No wake-up events detected
STANDBY
0
330k
or
strong
pulldown
0
1
Disabled
Wake-up detected from sleep
mode. TXD indicates wake-up
source. (Note 1)
NORMAL
SLOPE
1
330k
LIN
1
Normal slope
Enabled
(Notes 2, 3, 4)
LOW SLOPE
1
330k
LIN
1
Low slope
Enabled
(Notes 2, 3, 5)
FAULT*
1
330k
LIN
1
Disabled
Low power
—
DISABLE*
0
330k
LIN
High-Z
Disabled
Low power
—
Table 1. Operating Modes
Note 1: Standby mode is entered automatically after a local or remote wake-up event from sleep mode. INH and the 30k
termina-
tion resistor on LIN are enabled.
Note 2: The internal wake-up source flag on TXD is cleared upon entering normal slope or low slope mode.
Note 3: The internal wake-up interrupt flag on RXD is cleared upon entering normal slope or low slope mode.
Note 4: Drive NSLP high for longer than tGOTONORM with TXD logic-high to enter normal slope mode.
Note 5: Drive NSLP high for longer than tGOTONORM with TXD logic-low to enter low slope mode.
*
MAX13021 only.
High-Z = High impedance.
相關PDF資料 |
PDF描述 |
|---|---|
| AD9262BCPZ-5 | IC ADC 16BIT 5MHZ 64LFCSP |
| VE-B4F-MX-F3 | CONVERTER MOD DC/DC 72V 75W |
| UP050B910K-KEC | CAP CER 91PF 50V 10% AXIAL |
| VE-B4F-MX-F1 | CONVERTER MOD DC/DC 72V 75W |
| UP050B910K-B-B | CAP CER 91PF 50V 10% AXIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13020ASA+ | 功能描述:LIN 收發器 60V Fault-Protect RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MAX13020ASA+T | 功能描述:LIN 收發器 60V Fault-Protect RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
| MAX13021ASA/V+ | 制造商:Maxim Integrated Products 功能描述:+/-60V FAULT-PROTECTED LIN TRANSCEIVER - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC TXRX LIN 60V FAULT PRO 8-SOIC 制造商:Maxim Integrated Products 功能描述:60V+/- Fault Prot LIN Transceiver |
| MAX13021ASA/V+T | 制造商:Maxim Integrated Products 功能描述:+/-60V FAULT-PROTECTED LIN TRANSCEIVER - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC TXRX LIN 60V FAULT PRO 8-SOIC 制造商:Maxim Integrated Products 功能描述:60V+/- Fault Prot LIN Transceiver |
| MAX13021ASA+ | 功能描述:LIN 收發器 60V Fault-Protect RoHS:否 制造商:NXP Semiconductors 工作電源電壓: 電源電流: 最大工作溫度: 封裝 / 箱體:SO-8 |
發布緊急采購，3分鐘左右您將得到回復。