- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX13174ECAG+ (Maxim Integrated Products)IC CBL TERMINATION NETWRK 24SSOP PDF資料下載
參數資料
| 型號： | MAX13174ECAG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 10/13頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CBL TERMINATION NETWRK 24SSOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 58 |
| 類型： | 纜線 |
| 端子數： | 6 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 24-SSOP |
| 包裝： | 管件 |
MAX13174E
+5V Multiprotocol, Pin-Selectable
Cable Terminator
6
_______________________________________________________________________________________
The state of the MAX13174E’s mode-select pins—M0,
M1, M2, and DCE/DTE—determines the mode of each of
the six termination networks. Table 1 shows a cross-refer-
ence of termination mode and select pin state for each of
the six termination networks within the MAX13174E.
No-Cable Mode
The MAX13174E enters no-cable mode when the mode-
select inputs—M0, M1, and M2—are connected high. In
no-cable mode, all six termination networks are placed
in V.11 mode, with S1 closed and S2 open (Figure 4).
Applications Information
Older multiprotocol interface termination circuits have
been constructed using expensive relays with discrete
resistors, custom cables with built-in termination, or
complex circuit-board configurations to route signals to
the correct termination. The MAX13174E provides a
simple solution to this termination problem. All required
termination configurations are easily cable- or pin-
selectable using the four mode-control input pins (M0,
M1, M2, and DCE/DTE).
Using the MAX13174E in a Multiprotocol
Serial Interface
The MAX13174E terminator is designed to form a com-
plete +5V cable- or pin-selectable multiprotocol
DCE/DTE interface port when used with the
MAX13170E/MAX13172E differential drivers/receivers.
The MAX13174E terminator is designed to use the VEE
power generated by the MAX13171E’s charge pump
and meets all data sheet specifications when connect-
ed as illustrated in Figure 5. The mode-selection tables
of all three devices are identical, allowing the M0, M1,
M2, and DCE/DTE pins of each device to be connected
to a single 4-wire control bus. The MAX13170E and
MAX13172E provide internal pullups for the four lines,
Figure 3. Block Diagram
VCM =
±7V OR ±2V
VDM =
±2V
RDM =
VDM
R2 = 52
Ω
R3 = 127
Ω
R1 = 52
Ω
S1 ON
A
I
B
S2 OFF
AMMETER
Figure 1. V.11 or V.35 Differential Impedance Measurement
VCM =
±2V
R2 = 52
Ω
R3 = 127
Ω
R1 = 52
Ω
S1 ON
A
B
S2 ON
AMMETER
RCM =
VCM
I
Figure 2. V.35 Common-Mode Impedance Measurement
M2
123
456
5
2
1
24
23
22
21
4
6 7
9 10 16 15 18 17
14
19 20
3
8
11 12
13
VCC VEE
M1
M0
DCE/DTE
LATCH
MAX13174E
相關PDF資料 |
PDF描述 |
|---|---|
| MAX13184EESD+ | IC TXRX RS-485 +5.0V ESD 14SOIC |
| MAX13223EEUP+T | IC TXRX RS-232 2TX/2RX 20-TSSOP |
| MAX13234EAUP+ | TXRX RS-232 250KBPS 2X2 20TSSOP |
| MAX1329BETL+ | IC DAS 12BIT 300KSPS 40-TQFN-EP |
| MAX13342EEBC+T | IC TXRX USB FS 3WIRE 12-UCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13174ECAG+ | 功能描述:接口 - 專用 Pmic Fo Samsung Ap Proc C110/C111 RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX13174ECAG+T | 功能描述:接口 - 專用 +5V Multiprotocol, P In-Selectable Cable RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
| MAX13174EEAG+ | 制造商:Maxim Integrated Products 功能描述:+5V MULTIPROTOCOL PIN-SELECTABLE CABLE TERMINATOR - Rail/Tube |
| MAX13175EETU+ | 制造商:Maxim Integrated Products 功能描述:MULTIPROTOCOL PIN-SELECTABLE DATA INTERFACE CHIPSET - Rail/Tube |
| MAX13175EETU+T | 制造商:Maxim Integrated Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。