- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX13443EASA+T (Maxim Integrated Products)IC TXRX RS485 HALF DUPLEX 8-SOIC PDF資料下載
參數資料
| 型號： | MAX13443EASA+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS485 HALF DUPLEX 8-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS422，RS485 |
| 電源電壓： | 4.75 V ~ 5.25 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
MAX13442E/MAX13443E/MAX13444E
±15kV ESD-Protected, ±80V Fault-Protected,
Fail-Safe RS-485/J1708 Transceivers
16
______________________________________________________________________________________
J1708 Applications
The MAX13444E is designed for J1708 applications. To
configure the MAX13444E, connect DE and RE to GND.
Connect the signal to be transmitted to TXD. Terminate
the bus with the load circuit as shown in Figure 14. The
drivers used by SAE J1708 are used in a dominant-
mode application. DE is active low; a high input on DE
places the outputs in high impedance. When the driver is
disabled (TXD high or DE high), the bus is pulled high by
external bias resistors R1 and R2. Therefore, a logic-level
high is encoded as recessive. When all transceivers are
idle in this configuration, all receivers output logic-high
because of the pullup resistor on A and pulldown resistor
on B. R1 and R2 provide the bias for the recessive state.
C1 and C2 combine to form a lowpass filter, effective for
reducing FM interference. R2, C1, R4, and C2 combine
to form a 1.6MHz lowpass filter, effective for reducing
AM interference. Because the bus is unterminated, at
high frequencies, R3 and R4 perform a pseudotermina-
tion. This makes the implementation more flexible, as no
specific termination nodes are required at the ends of
the bus.
DI
RO
DE
A
B
RE
RO
DI
DE
D
R
BB
B
A
120
Ω
120
Ω
D
R
MAX13442E
MAX13443E
RE
Figure 13. MAX13442E/MAX13443E Typical RS-485 Network
相關PDF資料 |
PDF描述 |
|---|---|
| MAX13448EESD+T | IC TXRX RS485 FULL DUPLEX 14SOIC |
| MAX13450EAUD+ | TXRX RS-485 14TSSOP |
| MAX13482EETE+T | IC TXRX USB ESD PROT 16-TQFN |
| MAX13486EESA+ | IC TXRX RS485/422 8-SOIC |
| MAX13488EESA+T | IC TXRX RS485/RS422 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13444EASA | 功能描述:RS-485接口IC RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13444EASA/V+ | 功能描述:RS-485接口IC +/-80V Fault Protected RS-485 Half-Duplex Transceiver with Foldback Current Limit RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13444EASA/V+T | 功能描述:RS-485接口IC +/-80V Fault Protected RS-485 Half-Duplex Transceiver with Foldback Current Limit RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13444EASA+ | 功能描述:RS-485接口IC Half-Dplx RS-422/485 250ksps 5V LD/Rec RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13444EASA+T | 功能描述:RS-485接口IC Half-Dplx RS-422/485 250ksps 5V LD/Rec RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。