- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX13448EESD+T (Maxim Integrated Products)IC TXRX RS485 FULL DUPLEX 14SOIC PDF資料下載
參數資料
| 型號： | MAX13448EESD+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/14頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX RS485 FULL DUPLEX 14SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS485 |
| 電源電壓： | 3 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 14-SOIC |
| 包裝： | 帶卷 (TR) |
MAX13448E
±80V Fault-Protected Full-Duplex
RS-485 Transceiver
______________________________________________________________________________________
13
Hot-Swap Input Circuitry
The enable inputs feature hot-swap capability. At the
input there are two NMOS devices, M1 and M2 (Figure
9). When VCC ramps from zero, an internal 7s timer
turns on M2 and sets the SR latch that also turns on M1.
Transistor M2, a 1.5mA current sink, and M1, a 100A
current sink, pull DE to GND through a 5kΩ resistor. M2
is designed to pull DE to the disabled state against an
external parasitic capacitance up to 100pF that can
drive DE high. After 7s, the timer deactivates M2 while
M1 remains on, holding DE low against three-state leak-
ages that can drive DE high. M1 remains on until an
external source overcomes the required input current.
At this time, the SR latch resets and M1 turns off. When
M1 turns off, DE reverts to a standard, high-impedance
CMOS input.
Applications Information
256 Transceivers on the Bus
The RS-485 standard specifies the load each receiver
places on the bus in terms of unit loads. An RS-485
compliant transmitter can drive 32 one-unit loads when
used with a 120Ω cable that is terminated on both ends
over a common-mode range of -7V to +12V. The
MAX13448E is specified as 1/8 unit loads. This means
a compliant transmitter can drive up to 256 MAX13448E
devices. Reducing the common mode and/or changing
the characteristic impedance of the cable changes the
maximum number of receivers that can be used. Refer
to the TIA/EIA-485 specification for further details.
Proper Termination and Cabling/Wiring
Configurations
When the data rates for RS-485 are high relative to its
cable lengths, the system is subject to proper transmis-
sion line design. In most cases, a single, controlled-
impedance cable or trace should be used and should be
properly terminated on both ends with the characteristic
impedance of the cable/trace. RS-485 transceivers
should be connected to the cable/traces with minimum
length wires to prevent stubs. Star configurations and
improperly terminated cables can cause data loss. Refer
to the
Applications section of the Maxim website or to
TIA/EIA publication TSB89 for further information.
Reduced EMI and Reflections
The MAX13448E features reduced slew-rate drivers
that minimize EMI and reduce reflections caused by
improperly terminated cables, allowing error-free data
transmission up to 500kbps.
Line Length
The Telecommunications Industry Association (TIA)
publishes the document TSB-89:
Application
Guidelines for TIA/EIA-485-A that is a good reference
for determining maximum data rate vs. line length.
Typical Applications
The MAX13448E transceivers are designed for bidirec-
tional data communications on multipoint bus transmis-
sion lines. Figure 10 shows a typical network application
circuit. To minimize reflections, terminate the line at both
ends in its characteristic impedance, and keep stub
lengths off the main line as short as possible.
DE
(HOT SWAP)
5k
Ω
TIMER
VCC
10
μs
M2
M1
500
μA
100
μA
SR LATCH
Figure 9. Simplified Structure of the Driver Enable Pin (DE)
相關PDF資料 |
PDF描述 |
|---|---|
| MAX13450EAUD+ | TXRX RS-485 14TSSOP |
| MAX13482EETE+T | IC TXRX USB ESD PROT 16-TQFN |
| MAX13486EESA+ | IC TXRX RS485/422 8-SOIC |
| MAX13488EESA+T | IC TXRX RS485/RS422 8-SOIC |
| MAX1358BETL+W | DAS 16BIT DUAL 10:1 40-TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX13450EAUD+ | 功能描述:RS-485接口IC Half/Full-Dplx RS485 20Msps 5V LD/Rc RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13450EAUD+T | 功能描述:RS-485接口IC Half/Full-Dplx RS485 20Msps 5V LD/Rc RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13451EAUD+ | 功能描述:RS-485接口IC Full-Dplx RS485 20Msps 5V LD/Rc RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX13451EAUD+T | 功能描述:RS-485接口IC Full-Dplx RS485 20Msps 5V LD/Rc RoHS:否 制造商:Texas Instruments 數據速率:250 Kbps 工作電源電壓:3.3 V 電源電流:750 uA 工作溫度范圍:- 40 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX1346BETX | 功能描述:ADC / DAC多通道 RoHS:否 制造商:Texas Instruments 轉換速率: 分辨率:8 bit 接口類型:SPI 電壓參考: 電源電壓-最大:3.6 V 電源電壓-最小:2 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-40 |
發布緊急采購，3分鐘左右您將得到回復。