- 您現在的位置：買賣IC網 > PDF目錄9937 > MAX1446EHJ+T (Maxim Integrated Products)IC ADC 10BIT 60MSPS 32-TQFP PDF資料下載
參數資料
| 型號： | MAX1446EHJ+T |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 4/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10BIT 60MSPS 32-TQFP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 2,500 |
| 位數： | 10 |
| 采樣率（每秒）： | 60M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-TQFP |
| 供應商設備封裝： | 32-TQFP（5x5） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，雙極；1 個差分，雙極 |
MAX1446
10-Bit, 60Msps, 3.0V, Low-Power
ADC with Internal Reference
12
______________________________________________________________________________________
The MAX1446 provides three modes of reference oper-
ation:
Internal reference mode
Buffered external reference mode
Unbuffered external reference mode
In internal reference mode, the internal reference out-
put (REFOUT) can be tied to the REFIN pin through a
resistor (e.g., 10k
Ω) or resistor-divider if an application
requires a reduced full-scale range. For stability pur-
poses, it is recommended to bypass REFIN with a
> 10nF capacitor to GND.
In buffered external reference mode, the reference volt-
age levels can be adjusted externally by applying a
stable and accurate voltage at REFIN. In this mode,
REFOUT may be left open or connected to REFIN
through a > 10k
Ω resistor.
In unbuffered external reference mode, REFIN is con-
nected to GND, thereby deactivating the on-chip
buffers of REFP, COM, and REFN. With their buffers
shut down, these pins become high impedance and
can be driven by external reference sources.
Clock Input (CLK)
The MAX1446 CLK input accepts CMOS-compatible
clock signals. Since the interstage conversion of the
device depends on the repeatability of the rising and
falling edges of the external clock, use a clock with low
jitter and fast rise and fall times (< 2ns). In particular,
sampling occurs on the falling edge of the clock signal,
mandating this edge to provide lowest possible jitter.
Any significant aperture jitter would limit the SNR per-
formance of the ADC as follows:
where fIN represents the analog input frequency, and
tAJ is the time of the aperture jitter.
Clock jitter is especially critical for undersampling
applications. The clock input should always be consid-
ered as an analog input and routed away from any ana-
log input or other digital signal lines.
The MAX1446 clock input operates with a voltage
threshold set to VDD/2. Clock inputs with a duty cycle
other than 50% must meet the specifications for high
and low periods as stated in the
Electrical Character-
istics. See Figures 3a, 3b, 4a, and 4b for the relation-
ship between spurious-free dynamic range (SFDR),
signal-to-noise ratio (SNR), total harmonic distortion
(THD), or signal-to-noise plus distortion (SINAD) vs.
duty cycle.
Output Enable (
OE), Power-Down (PD),
and Output Data (D0–D9)
All data outputs, D0 (LSB) through D9 (MSB), are
TTL/CMOS-logic compatible. There is a 5.5 clock-cycle
latency between any particular sample and its valid
output data. The output coding is straight offset binary
(Table 1). With
OE and PD (power-down) high, the digi-
tal output enters a high-impedance state. If
OE is held
low with PD high, the outputs are latched at the last
value prior to the power-down.
The capacitive load on the digital outputs D0–D9
should be kept as low as possible (< 15pF) to avoid
large digital currents that could feed back into the ana-
log portion of the MAX1446, degrading its dynamic per-
formance. The use of buffers on the ADC’s digital
outputs can further isolate the digital outputs from
heavy capacitive loads.
To further improve the dynamic performance of the
MAX1446 small series resistors (e.g., 100
Ω) may be
added to the digital output paths, close to the ADC.
Figure 5 displays the timing relationship between out-
put enable and data output valid, as well as power-
down/wake-up and data output valid.
System Timing Requirements
Figure 6 shows the relationship between the clock
input, analog input, and data output. The MAX1446
SNR
ft
IN
AJ
=×
××
×
20
1
2
log
π
Table 1. MAX1446 Output Code for Differential Inputs
DIFFERENTIAL INPUT VOLTAGE*
DIFFERENTIAL INPUT
STRAIGHT OFFSET BINARY
VREF
× 511/512
+Full Scale -1LSB
11 1111 1111
VREF
× 510/512
+Full Scale -2LSB
11 1111 1110
VREF
× 1/512
+1LSB
10 0000 0001
0
Bipolar Zero
10 0000 0000
- VREF
× 1/512
-1LSB
01 1111 1111
- VREF
× 511/512
Negative Full Scale + 1LSB
00 0000 0001
- VREF
× 512/512
Negative Full Scale
00 0000 0000
*VREFIN = VREFP = VREFN
相關PDF資料 |
PDF描述 |
|---|---|
| IDT723632L12PQF | IC FIFO SYNC 512X36X2 132QFP |
| MS27473E18A28S | CONN PLUG 28POS STRAIGHT W/SCKT |
| MAX113EAG+T | IC ADC 8BIT 400KSPS 24-SSOP |
| VI-J14-MW-B1 | CONVERTER MOD DC/DC 48V 100W |
| VI-BWZ-MV-F4 | CONVERTER MOD DC/DC 2V 60W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1446GHJ+ | 功能描述:模數轉換器 - ADC 10-Bit 60Msps 3V High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1446GHJ+T | 功能描述:模數轉換器 - ADC 10-Bit 60Msps 3V High Speed ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1447ECJ | 功能描述:模數轉換器 - ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1447ECJ+ | 功能描述:模數轉換器 - ADC 4.5-Digit 5sps ADC w/LED Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| MAX1447ECJ+T | 功能描述:模數轉換器 - ADC 4.5-Digit 5sps ADC w/LED Drivers RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
發布緊急采購，3分鐘左右您將得到回復。