- 您現在的位置：買賣IC網 > PDF目錄1936 > MAX1480ECEPI+ (Maxim Integrated Products)IC RS485/RS422 DATA INTRFC 28DIP PDF資料下載
參數資料
| 型號： | MAX1480ECEPI+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 19/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC RS485/RS422 DATA INTRFC 28DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 14 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 1/1 |
| 規程： | RS422，RS485 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 28-DIP（0.600"，15.24mm） |
| 供應商設備封裝： | 28-PDIP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1402 (CN2011-ZH PDF) |
MAX1480E/MAX1490E
±15kV ESD-Protected, Isolated RS-485/RS-422
Data Interfaces
_______________________________________________________________________________________
9
Detailed Description
The MAX1480EA/MAX1480EC/MAX1490EA/MAX1490EB
are complete, electrically isolated, RS-485/RS-422 data-
communications interface solutions. Transceivers, opto-
couplers, a power driver, and a transformer in one
standard 28-pin DIP package (24-pin package for the
MAX1490EA/MAX1490EB) provide a complete inter-
face. Signals and power are internally transported
across the isolation barrier (Figures 1, 2). Power is
transferred from the logic side (nonisolated side) to the
isolated side of the barrier through a center-tapped
transformer. Signals cross the barrier through high-
speed optocouplers. A single +5V supply on the logic
side powers both sides of the interface. The
MAX1480EA/MAX1480EC offer half-duplex communica-
tions while the MAX1490EA/MAX1490EB feature full-
duplex communication. The functional input/output
relationships are shown in Tables 3 through 6.
The MAX1480EC/MAX1490EB feature reduced-slew-rate
drivers that minimize EMI and reduce reflections caused
by improperly terminated cables, allowing error-free
transmission at data rates up to 160kbps. The
MAX1480EA/MAX1490EA driver slew rate is not limited,
allowing transmission rates up to 2.5Mbps.
The MAX1480EC/MAX1490EB shutdown feature reduces
supply current to as low as 0.2A by using the SD pin (see
Low-Power Shutdown Mode section).
Drivers are short-circuit current limited and are protect-
ed against excessive power dissipation by thermal
shutdown circuitry that puts the driver outputs into a
high-impedance state. The receiver input has a fail-safe
feature that guarantees a logic-high RO (logic-low RO)
output if the input is open circuit.
On the MAX1480EA/MAX1480EC, the driver outputs are
enabled by bringing DE
high. Driver-enable time is typi-
cally 1.0s. Allow time for the devices to be
enabled before sending data (see Typical Operating
Characteristics). When enabled, driver outputs function
as line drivers. Driver outputs are high impedance when
DE
is low. When outputs are high impedance, they func-
tion as line receivers.
The MAX1480EA/MAX1480EC/MAX1490EA/MAX1490EB
withstand 1260VRMS (1min) or 1520VRMS (1s). The logic
inputs can be driven from TTL/CMOS logic with a series
resistor, and the received data output can directly drive
TTL or CMOS-logic families with only a resistive pullup.
Low-Power Shutdown Mode
The SD pin shuts down the oscillator on the internal power
driver. With the primary side in shutdown, no power is
transferred across the isolation barrier. The DI and DE
optocouplers, however, still consume current if the drive
signals on the nonsolated side are low. Therefore, leave
DI
and DE high or floating when in shutdown mode.
Under these conditions, the MAX1480EC/MAX1490EB
supply current is reduced to as low as 0.2A.
___________________________________________________Pin Description (continued)
Note: For DE
and DI pin descriptions, see Detailed Block Diagram and Typical Application Circuit (Figure 1 for MAX1480EA/
MAX1480EC, Figure 2 for MAX1490EA/MAX1490EB).
Internal Connections. Leave these pins unconnected.
AC2, AC1
23, 24
27, 28
26
22
ISO VCC1
Isolated Supply Voltage Source
Inverting Driver Output and Inverting Receiver Input
B
—
25
Isolated Receiver-Output Drive. Connect to ISO RO LED through a resistor (see
Table 1 for MAX1480EA/MAX1480EC, Table 2 for MAX1490EA/MAX1490EB).
ISO RO DRV
21
24
23
—
A
Noninverting Driver Output and Noninverting Receiver Input
Isolated Driver Input. Connect to ISO DI DRV for normal operation.
ISO DI IN
—
22
Isolated Driver-Enable Input. Connect to ISO DE DRV for normal operation.
ISO DE IN
—
21
Noninverting Receiver Input
A
20
—
Inverting Receiver Input
B
19
—
Inverting Driver Output
Z
18
—
Noninverting Driver Output
Y
17
—
FUNCTION
NAME
MAX1490EA/
MAX1490EB
MAX1480EA/
MAX1480EC
PIN
相關PDF資料 |
PDF描述 |
|---|---|
| MAX14820ETG+ | IC IO-LINK TXRX 24TQFN |
| MAX14821ETG+ | IC IO-LINK 24-TQFN |
| MAX14824GTG+ | IC IO-LINK MASTER TXRX 24TQFN |
| MAX1482CSD-T | IC TXRX RS485/422 250KBPS 14SOIC |
| MAX14830ETM+ | SEMICONDUCTOR OTHER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1480ECEPI+ | 功能描述:RS-422/RS-485 接口 IC Isolated RS-422/485 Data Interface RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
| MAX14811CTN+ | 制造商:Maxim Integrated Products 功能描述:DUAL, UNIPOLAR/BIPOLAR, HIGH-VOLTAGE DIGITAL PULSERS WITH FA - Rail/Tube |
| MAX14811CTN+T | 制造商:Maxim Integrated Products 功能描述:DUAL, UNIPOLAR/BIPOLAR, HIGH-VOLTAGE DIGITAL PULSERS WITH FA - Tape and Reel |
| MAX1481CPD | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1481CUB | 功能描述:RS-422/RS-485 接口 IC RoHS:否 制造商:Maxim Integrated 數據速率:1136 Kbps 工作電源電壓:3 V to 5.5 V 電源電流:5.9 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-28 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。