- 您現在的位置：買賣IC網 > PDF目錄385521 > MAX15003 (Maxim Integrated Products, Inc.) Triple-Output Buck Controller with Tracking/Sequencing PDF資料下載
參數資料
| 型號： | MAX15003 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Triple-Output Buck Controller with Tracking/Sequencing |
| 中文描述： | 三輸出buck控制器，提供跟蹤/排序功能 |
| 文件頁數： | 12/32頁 |
| 文件大?。?/td> | 945K |
| 代理商： | MAX15003 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
M
Triple-Output Buck Controller with
Tracking/Sequencing
12
______________________________________________________________________________________
Pin Description (continued)
PIN
NAME
FUNCTION
33
EN/TRACK3
Controller 3 Enable/Tracking Input. See Figure 2.
When sequencing, EN/TRACK3 must be above 1.24V for the PWM controller 3 to start.
Coincident tracking—connect the same resistive divider used for FB3, from Output 1 to EN/TRACK3 to
SGND.
Ratiometric tracking—connect EN/TRACK3 to analog ground.
34
COMP3
Controller 3 Error Transconductance Amplifier Output. Connect COMP3 to the compensation feedback
network.
35
ILIM3
Controller 3 Valley Current-Limit Set Output. Connect a 25k
to 150k
resistor, R
ILIM3
, from ILIM3 to SGND
to program the valley current-limit threshold from 50mV to 300mV. ILIM3 sources 20μA out to R
ILIM3
. The
resulting voltage divided by 10 is the valley current-limit threshold. When using a precision current-sense
resistor, connect a resistive divider from REG to ILIM3 to SGND to set the valley current limit. See Figure 11.
36
CSP3
Controller 3 Positive Current-Sense Input. Connect CSP3 to the synchronous MOSFET source (connected to
PGND3). When using a current-sense resistor, connect CSP3 to the PGND3 end of the current-sense
resistor.
37
CSN3
Controller 3 Negative Current-Sense Input. Connect CSN3 to the synchronous MOSFET drain (connected to
LX3). When using a current-sense resistor, connect CSN3 to the junction of low-side MOSFET’s source and
the current-sense resistor. See Figure 11.
38
BST3
Controller 3 High-Side Gate Driver Supply. Connect BST3 to the cathode of the boost diode and to the
positive terminal of the boost capacitor.
39
DH3
Controller 3 High-Side Gate Driver Output. DH3 drives the gate of the high-side MOSFET.
40
LX3
Controller 3 High-Side MOSFET Source Connection/Synchronous MOSFET Drain Connection. Connect the
inductor and the negative side of the boost capacitor to LX3.
41
DREG3
Controller 3 Low-Side Gate Driver Supply. Connect externally to REG and anode of the boost diode.
Connect a minimum of 0.1μF ceramic capacitor from DREG3 to PGND3.
42
DL3
Controller 3 Low-Side Gate Driver Output. DL3 is the gate driver output for the synchronous MOSFET.
43
PGND3
Controller 3 Power-Ground Connection. Connect the input filter capacitor’s negative terminal, the source of
the synchronous MOSFET, and the output filter capacitor’s return to PGND3. Connect externally to SGND at
a single point near the input capacitor return terminal.
44
SYNC
Synchronization Input. Drive with a frequency at least 20% higher than three times the frequency
programmed using the RT pin. The switching frequency is 1/3 the SYNC frequency. Connect SYNC to
SGND when not used.
45
SGND
Analog Ground Connection. Connect SGND and PGND_ together at one point near the input bypass
capacitor return terminal.
46
RT
Oscillator Timing Resistor Connection. Connect a 500k
to 45k
resistor from RT to SGND to program the
switching frequency from 200kHz to 2.2MHz.
47
PHASE
Phase Select Input. Connect PHASE to SGND for 120° out-of-phase operation between the controllers.
Connect to REG for in phase operation.
48
RESET
RESET
Output. Open-drain
RESET
output releases after all PGOODs are released and timeout programmed
by CT finishes.
—
EP
Exposed Pad. Solder the exposed pad to a large SGND plane.
相關PDF資料 |
PDF描述 |
|---|---|
| MAX15008 | Automotive 300mA LDO Voltage Regulators with Tracker Output and Overvoltage Protector |
| MAX15010 | Automotive 300mA LDO Voltage Regulators with Tracker Output and Overvoltage Protector |
| MAX15009 | Automotive 300mA LDO Regulators with Switched Output and Overvoltage Protector |
| MAX15011 | Automotive 300mA LDO Regulators with Switched Output and Overvoltage Protector |
| MAX15024 | Single/Dual, 16ns, High Sink/Source Current Gate Drivers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX15003ATM+ | 功能描述:DC/DC 開關控制器 Triple-Out Buck Ctlr w/Track/Sequence RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX15003ATM+T | 功能描述:DC/DC 開關控制器 Triple-Out Buck Ctlr w/Track/Sequence RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX15003EVKIT+ | 功能描述:電源管理IC開發工具 MAX15003 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX15004AAUE/V+ | 功能描述:電流型 PWM 控制器 Flyback/Boost/SEPIC Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| MAX15004AAUE/V+T | 功能描述:電流型 PWM 控制器 Flyback/Boost/SEPIC Power-Supply Ctlr RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
發布緊急采購，3分鐘左右您將得到回復。