- 您現在的位置：買賣IC網 > PDF目錄385521 > MAX1514ETP (MAXIM INTEGRATED PRODUCTS INC) TFT-LCD Power-Supply Controllers PDF資料下載
參數資料
| 型號： | MAX1514ETP |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | TFT-LCD Power-Supply Controllers |
| 中文描述： | SWITCHING CONTROLLER, 1725 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | 4 X 4 MM, 0.80 MM HEIGHT, MO-220-VGGD, TQFN-20 |
| 文件頁數： | 27/28頁 |
| 文件大?。?/td> | 540K |
| 代理商： | MAX1514ETP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁
M
TFT-LCD Power-Supply Controllers
______________________________________________________________________________________
27
PC Board Layout and Grounding
Careful PC board layout is important for proper operation.
Use the following guidelines for good PC board layout:
1) Minimize the area of high-current loops. The high-
current input loop goes from the positive terminals of
the input capacitors to the inductor, to the power
MOSFET, and to the negative terminals of the input
capacitors. The high-current output loop is from the
positive terminals of the input capacitors to the
inductor, to the output diode, and to the positive ter-
minals of the output capacitors, reconnecting
between the output-capacitor and input-capacitor
ground terminals. Connect these loops with short,
wide connections. Avoid using vias in the high-cur-
rent paths. If vias are unavoidable, use many vias in
parallel to reduce resistance and inductance.
2) Create a power ground plane consisting of the input
and output-capacitor ground terminals, the source of
the power MOSFET, and any ground terminals of the
charge-pump components. Connect all of these
together with short, wide traces or a small ground
plane. Maximizing the width of the power ground
traces improves efficiency and reduces output volt-
age ripple and noise spikes. Create an analog
ground plane consisting of the IC’s backside pad, all
the feedback-divider ground connections, the buffer-
amplifier-divider ground connection, the REF capaci-
tor ground connection, and the DEL capacitor ground
connection. The power ground plane and the analog
ground plane should be connected at only one loca-
tion, which is the IC’s GND pin. All other ground con-
nections, such as the IN pin bypass capacitor and
the linear-regulator output capacitors, should be star-
connected directly to the backside pad of the IC
through a via with wide traces, not otherwise connect-
ing to either the power ground plane or the analog
ground plane. Connect the IC’s backside pad to the
IC’s GND pin. Make no other connections between
the analog and power ground planes.
3) Place IN and REF bypass capacitors as close to the
device as possible.
4) Place all feedback-voltage-divider resistors as close
to their respective feedback pins as possible. The
divider’s center trace should be kept short. Placing
the resistors far away causes their FB traces to
become antennas that can pick up switching noise.
Care should be taken to avoid running any feedback
trace near the switching nodes in the step-up regu-
lator and charge pumps.
5) Minimize the length and maximize the width of the
traces between the output capacitors and the load
for best transient responses.
6) Minimize the size of the switching node while keeping
it wide and short. Keep the switching node away from
feedback nodes (FB, FBP, FBL, FBG, and FBN) and
analog ground. Use DC traces to shield if necessary.
Refer to the MAX1513 evaluation kit for an example of
proper board layout.
Chip Information
TRANSISTOR COUNT: 4807
PROCESS: BiCMOS
Pin Configuration
F
C
C
I
20
19
18
17
16
G
*FBG
FBP
DRVP
GND
*DRVG
13
12
11
14
15
*OUTB
*FBPB
SDFR
REF
*SUPB
4
3
2
1
5
F
D
D
D
6
7
8
9
10
F
MAX1513
MAX1514
TOP VIEW
THIN QFN
4mm x 4mm
*N.C. FOR MAX1514
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1518B | TFT-LCD DC-DC Converter with Operational Amplifiers |
| MAX1518BETJ | TFT-LCD DC-DC Converter with Operational Amplifiers |
| MAX1538ETI | Power-Source Selector for Dual-Battery Systems |
| MAX154 | CMOS High-Speed 4-Bit ADCs with Multiplexer and Reference(8位,4通道,400ksps,并行A/D轉換器) |
| MAX1558 | Dual, 3mm x 3mm, 1.2A/Programmable-Current USB Switches with Autoreset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1514ETP+T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1514ETP-T | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1515ETG | 功能描述:直流/直流開關調節器 RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MAX1515ETG+ | 功能描述:直流/直流開關調節器 3A 1MHz Step-Down DDR Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
| MAX1515ETG+T | 功能描述:直流/直流開關調節器 3A 1MHz Step-Down DDR Regulator RoHS:否 制造商:International Rectifier 最大輸入電壓:21 V 開關頻率:1.5 MHz 輸出電壓:0.5 V to 0.86 V 輸出電流:4 A 輸出端數量: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:PQFN 4 x 5 |
發布緊急采購，3分鐘左右您將得到回復。