- 您現在的位置：買賣IC網 > PDF目錄385521 > MAX1518B (Maxim Integrated Products, Inc.) TFT-LCD DC-DC Converter with Operational Amplifiers PDF資料下載
參數資料
| 型號： | MAX1518B |
| 廠商： | Maxim Integrated Products, Inc. |
| 元件分類： | DC/DC變換器 |
| 英文描述： | TFT-LCD DC-DC Converter with Operational Amplifiers |
| 中文描述： | TFT-LCD DC-DC轉換器，帶有運算放大器 |
| 文件頁數： | 22/25頁 |
| 文件大小： | 1308K |
| 代理商： | MAX1518B |
M
TFT-LCD DC-DC Converter with
Operational Amplifiers
22
______________________________________________________________________________________
The transconductance amplifier regulates the output
voltage by controlling the pass transistor’s base cur-
rent. The total DC loop gain is approximately:
where V
T
is 26mV at room temperature, and I
BIAS
is the
current through the base-to-emitter resistor (R
BE
). For
the MAX1518B, the bias currents for both the gate-on
and gate-off linear-regulator controllers are 0.1mA.
Therefore, the base-to-emitter resistor for both linear
regulators should be chosen to set 0.1mA bias current:
V
mA
0 1
.
The output capacitor and the load resistance create the
dominant pole in the system. However, the internal
amplifier delay, pass transistor’s input capacitance,
and the stray capacitance at the feedback node create
additional poles in the system, and the output capaci-
tor’s ESR generates a zero. For proper operation, use
the following equations to verify the linear regulator is
properly compensated:
1) First, determine the dominant pole set by the linear
regulator’s output capacitor and the load resistor:
The unity-gain crossover of the linear regulator is:
f
CROSSOVER
= A
V_LR
f
POLE_LR
2) The pole created by the internal amplifier delay is
approximately 1MHz:
f
POLE_AMP
= 1MHz
3) Next, calculate the pole set by the transistor’s
input capacitance, the transistor’s input resistance,
and the base-to-emitter pullup resistor:
g
m
is the transconductance of the pass transistor,
and f
T
is the transition frequency. Both parameters
can be found in the transistor’s data sheet. Because
R
BE
is much greater than R
IN
, the above equation
can be simplified:
Substituting for C
IN
and R
IN
yields:
4) Next, calculate the pole set by the linear regula-
tor’s feedback resistance and the capacitance
between FB_ and AGND (including stray capaci-
tance):
where C
FB
is the capacitance between FB_ and
AGND, R
UPPER
is the upper resistor of the linear
regulator’s feedback divider, and R
LOWER
is the
lower resistor of the divider.
5) Next, calculate the zero caused by the output
capacitor’s ESR:
where R
ESR
is the equivalent series resistance of
C
OUT_LR
.
To ensure stability, choose C
OUT_LR
large enough so
the crossover occurs well before the poles and zero
calculated in steps 2 to 5. The poles in steps 3 and 4
generally occur at several megahertz, and using
ceramic capacitors ensures the ESR zero occurs at
several megahertz as well. Placing the crossover below
500kHz is sufficient to avoid the amplifier-delay pole
and generally works well, unless unusual component
choices or extra capacitances move one of the other
poles or the zero below 1MHz.
f
C
R
POLE ESR
OUT LR
ESR
_
_
=
×
×
1
2
π
f
C
R
(
R
POLE FB
FB
UPPER
LOWER
_
||
)
=
×
×
1
2
π
f
f
h
POLE IN
T
FE
_
=
f
C
R
POLE IN
IN
IN
_
=
×
×
1
2
π
where C
g
2
π
f
R
h
g
IN
m
T
IN
FE
m
=
=
,
,
f
C
R
(
R
POLE IN
IN
BE
IN
_
||
)
=
×
×
1
2
π
f
I
C
V
POLE LR
LOAD MAX
LR
OUT LR
OUT LR
_
(
)_
_
_
=
×
×
2
π
R
V
mA
k
BE
BE
=
≈
0 7
0 1
.
6 8
.
.
A
V
I
h
I
V
V LR
_
T
BIAS
LOAD LR
FE
REF
_
×
+
×
×
10
1
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1518BETJ | TFT-LCD DC-DC Converter with Operational Amplifiers |
| MAX1538ETI | Power-Source Selector for Dual-Battery Systems |
| MAX154 | CMOS High-Speed 4-Bit ADCs with Multiplexer and Reference(8位,4通道,400ksps,并行A/D轉換器) |
| MAX1558 | Dual, 3mm x 3mm, 1.2A/Programmable-Current USB Switches with Autoreset |
| MAX1558ETB | Dual, 3mm x 3mm, 1.2A/Programmable-Current USB Switches with Autoreset |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1518BETJ+ | 功能描述:LCD 驅動器 TFT-LCD DC-DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MAX1518BETJ+T | 功能描述:LCD 驅動器 TFT-LCD DC-DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MAX1518ETJ | 功能描述:LCD 驅動器 RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MAX1518ETJ+ | 功能描述:LCD 驅動器 TFT-LCD DC-DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
| MAX1518ETJ+T | 功能描述:LCD 驅動器 TFT-LCD DC-DC Conv w/Op Amps RoHS:否 制造商:Maxim Integrated 數位數量:4.5 片段數量:30 最大時鐘頻率:19 KHz 工作電源電壓:3 V to 3.6 V 最大工作溫度:+ 85 C 最小工作溫度:- 20 C 封裝 / 箱體:PDIP-40 封裝:Tube |
發布緊急采購，3分鐘左右您將得到回復。