- 您現在的位置：買賣IC網 > PDF目錄383325 > MAX1540A (Maxim Integrated Products, Inc.) Dual Step-Down Controllers with Saturation Protection, Dynamic Output, and Linear Regulator PDF資料下載
參數資料
| 型號： | MAX1540A |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | Dual Step-Down Controllers with Saturation Protection, Dynamic Output, and Linear Regulator |
| 中文描述： | 雙路、降壓型控制器，帶有電感飽和保護、動態輸出和線性穩壓器 |
| 文件頁數： | 39/49頁 |
| 文件大小： | 794K |
| 代理商： | MAX1540A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁當前第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁
Output-Capacitor Stability Considerations
For Quick-PWM controllers, stability is determined by
the value of the ESR zero relative to the switching fre-
quency. The boundary of instability is given by the fol-
lowing equation:
For a typical 300kHz application, the ESR zero frequen-
cy must be well below 95kHz, preferably below 50kHz.
Tantalum and OS-CON capacitors in widespread use
at the time of publication have typical ESR zero fre-
quencies of 25kHz. In the design example used for
inductor selection, the ESR needed to support 25mV
P-P
ripple is 25mV/1.2A = 20.8m
Ω
. One 220μF/4V Sanyo
polymer (TPE) capacitor provides 15m
Ω
(max) ESR.
This results in a zero at 48kHz, well within the bounds
of stability.
Do not put high-value ceramic capacitors directly
across the feedback sense point without taking precau-
tions to ensure stability. Large ceramic capacitors can
have a high-ESR zero frequency and cause erratic,
unstable operation. However, it is easy to add enough
series resistance by placing the capacitors a couple of
inches downstream from the feedback sense point,
which should be as close as possible to the inductor.
Unstable operation manifests itself in two related but
distinctly different ways: double pulsing and fast-feed-
back loop instability. Double pulsing occurs due to
noise on the output or because the ESR is so low that
there is not enough voltage ramp in the output voltage
signal. This “fools” the error comparator into triggering
a new cycle immediately after the 400ns minimum off-
time period has expired. Double pulsing is more annoy-
ing than harmful, resulting in nothing worse than
increased output ripple. However, it can indicate the
possible presence of loop instability due to insufficient
ESR. Loop instability can result in oscillations at the out-
put after line or load steps. Such perturbations are usu-
ally damped, but can cause the output voltage to rise
above or fall below the tolerance limits.
The easiest method for checking stability is to apply a
very fast zero-to-max load transient and carefully
observe the output voltage ripple envelope for over-
shoot and ringing. It can help to monitor simultaneously
the inductor current with an AC current probe. Do not
allow more than one cycle of ringing after the initial
step-response under/overshoot.
Input-Capacitor Selection
The input capacitor must meet the ripple current
requirement (I
RMS
) imposed by the switching currents:
For most applications, nontantalum chemistries (ceram-
ic, aluminum, or OS-CON) are preferred due to their
resistance to power-up surge currents typical of sys-
tems with a mechanical switch or connector in series
with the input. If the MAX1540A/MAX1541 are operated
as the second stage of a two-stage power conversion
system, tantalum input capacitors are acceptable. In
either configuration, choose a capacitor that has less
than 10°C temperature rise at the RMS input current for
optimal reliability and lifetime.
Power MOSFET Selection
Most of the following MOSFET guidelines focus on the
challenge of obtaining high load-current capability
when using high-voltage (>20V) AC adapters. Low-cur-
rent applications usually require less attention.
The high-side MOSFET (N
H
) must be able to dissipate
the resistive losses plus the switching losses at both
V
IN(MIN)
and V
IN(MAX)
. Ideally, the losses at V
IN(MIN)
should be roughly equal to the losses at V
IN(MAX)
, with
lower losses in between. If the losses at V
IN(MIN)
are
significantly higher, consider increasing the size of N
H
.
Conversely, if the losses at V
IN(MAX)
are significantly
higher, consider reducing the size of N
H
. If V
IN
does
not vary over a wide range, maximum efficiency is
achieved by selecting a high-side MOSFET (N
H
) that
has conduction losses equal to the switching losses.
Choose a low-side MOSFET (N
L
) that has the lowest pos-
sible on-resistance (R
DS(ON)
), comes in a moderate-sized
package (i.e., 8-pin SO, DPAK, or D
2
PAK), and is reason-
ably priced. Ensure that the MAX1540A/MAX1541 DL_
gate driver can supply sufficient current to support the
gate charge and the current injected into the parasitic
drain-to-gate capacitor caused by the high-side MOSFET
turning on; otherwise, cross-conduction problems may
occur. Switching losses are not an issue for the low-side
MOSFET since it is a zero-voltage switched device when
used in the step-down topology.
V
IN
I
2OUTX
V
OUTX
(V
IN
- V
OUTX
)
2
Σ
X = 1
I
RMS
=
f
f
where:
f
1
2 R
ESR
SW
π
ESR
ESR OUT
≤
=
M
Dual Step-Down Controllers with Saturation
Protection, Dynamic Output, and Linear Regulator
______________________________________________________________________________________
39
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1540AETJ | Dual Step-Down Controllers with Saturation Protection, Dynamic Output, and Linear Regulator |
| MAX1543 | TFT LCD DC-to-DC Converter with Operational Amplifiers |
| MAX1542 | TFT LCD DC-to-DC Converter with Operational Amplifiers |
| MAX1542-MAX1543 | TFT LCD DC-to-DC Converter with Operational Amplifiers |
| MAX1543ETP | TFT LCD DC-to-DC Converter with Operational Amplifiers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1540AETJ+ | 功能描述:DC/DC 開關控制器 Dual Step-Down Ctlr w/Saturation Prot RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1540AETJ+T | 功能描述:DC/DC 開關控制器 Dual Step-Down Ctlr w/Saturation Prot RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1540ETJ | 功能描述:DC/DC 開關控制器 RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1540ETJ+ | 功能描述:DC/DC 開關控制器 Dual Step-Down Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| MAX1540ETJ+T | 功能描述:DC/DC 開關控制器 Dual Step-Down Ctlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
發布緊急采購，3分鐘左右您將得到回復。