- 您現在的位置：買賣IC網 > PDF目錄383325 > MAX1561ETA (MAXIM INTEGRATED PRODUCTS INC) High-Efficiency, 26V Step-Up Converters for Two to Six White LEDs PDF資料下載
參數資料
| 型號： | MAX1561ETA |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 顯示驅動器 |
| 英文描述： | High-Efficiency, 26V Step-Up Converters for Two to Six White LEDs |
| 中文描述： | LED DISPLAY DRIVER, DSO8 |
| 封裝： | 3 X 3 MM, 0.80 MM PITCH, DFN-8 |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 245K |
| 代理商： | MAX1561ETA |
M
High-Efficiency, 26V Step-Up Converters
for Two to Six White LEDs
6
_______________________________________________________________________________________
Detailed Description
The MAX1561/MAX1599s
’
high efficiency and small size
make them ideally suited to drive up to six series-con-
nected LEDs. The device operates as a boost DC-DC
converter that regulates output current rather than volt-
age. The MAX1561/MAX1599 provide even illumination
by sourcing the same output current through each LED,
eliminating the need for expensive factory calibration.
The fast 1MHz (500kHz for the MAX1599) internal oscil-
lator allows for a small inductor and small input and out-
put capacitors while minimizing input and output ripple.
The single analog control input allows easy adjustment
of LED brightness and on/off control. This allows either
simple logic-level on/off control, analog voltage control,
or PWM duty-cycle control of both brightness and shut-
down. In shutdown, supply current is reduced to a low
0.3μA. A soft-start gradually illuminates the LEDs, elimi-
nating the inrush current during startup.
Soft-Start
The MAX1561/MAX1599 attain soft-start by charging
C
COMP
gradually with a current source. When V
COMP
rises above 1.25V, the internal MOSFET begins switch-
ing at a reduced duty cycle. When V
COMP
rises above
2.25V, the duty cycle is at its maximum. See the
Typical
Operating Characteristics
for an example of soft-start
operation.
Shutdown
The MAX1561/MAX1599 enter shutdown when V
CTRL
is
less than 100mV for more than 8.2ms (16.4ms for the
MAX1599). In shutdown, supply current is reduced to
0.3μA by powering down the entire IC except for the
CTRL voltage-detection circuitry. C
COMP
is discharged
during shutdown, allowing the device to reinitiate soft-
start when it is enabled. Although the internal N-chan-
nel MOSFET does not switch in shutdown, there is still
a DC current path between the input and the LEDs
through the inductor and Schottky diode. The minimum
forward voltage of the LED array must exceed the max-
imum input voltage to ensure that the LEDs remain off
in shutdown. However, with two or more LEDs, the for-
ward voltage is large enough to keep leakage current
low, less than 1μA (typ). Typical shutdown timing char-
acteristics are shown in the
Typical Operating
Characteristic
s.
Overvoltage Protection
Overvoltage lockout (OVLO) occurs when V
OUT
is
above 27V. The protection circuitry stops the internal
MOSFET from switching and causes V
COMP
to decay
to 0V. The device comes out of OVLO and into soft-
start when V
OUT
falls below 25V.
PIN
NAME
FUNCTION
1
OUT
Overvoltage Sense. When V
OUT
is greater than 27V, the internal N-channel MOSFET turns off until V
OUT
drops below 25V, then the IC reenters soft-start. Connect a 0.1μF capacitor from OUT to PGND.
2
IN
Input Voltage Supply. Input voltage range is 2.6V to 5.5V. Connect a 2.2μF capacitor from IN to PGND.
Brightness Control Input. LED brightness is controlled by the voltage applied to CTRL. Varying the voltage
from 0.24V to 1.62V adjusts the brightness from dim to bright, respectively. Any voltage above 1.62V does
not increase brightness. If CTRL is held below 100mV for more than 8.2ms (16.4ms for the MAX1599), the
IC shuts down.
Current-Sense Feedback Input. Connect a resistor from CS to GND to set the LED bias current. The
voltage at CS regulates to V
CTRL
/ 10 or 0.162V, whichever is lower.
3
CTRL
4
CS
5
COMP
Compensation Input. Connect a 0.1μF capacitor (C
COMP
) from COMP to GND. C
COMP
stabilizes the
converter and controls soft-start. C
COMP
discharges to GND when in shutdown.
Ground. Connect to PGND and the exposed pad directly under the IC.
Power Ground. Connect to GND and the exposed pad directly under the IC.
Inductor Connection. This pin is high impedance during shutdown.
6
7
8
GND
PGND
LX
Exposed
Pad
EP
Ground. Connect directly to GND and PGND under the IC.
Pin Description
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1561 | High-Efficiency. 26V Step-Up Converters for Two to Six White LEDs |
| MAX1599 | High-Efficiency. 26V Step-Up Converters for Two to Six White LEDs |
| MAX1599ETA | High-Efficiency, 26V Step-Up Converters for Two to Six White LEDs |
| MAX1562-MAX1563 | Programmable 4A USB Current-Limited Switches with Autoreset and Fault Blanking |
| MAX1562 | Programmable. 4A. USB. Current-Limited Switches with Autoreset and Fault Blanking |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1561ETA+ | 制造商:Maxim Integrated Products 功能描述:LED DRVR 6SEGMENT 3.3V/5V 8TDFN EP - Rail/Tube |
| MAX1561ETA+T | 功能描述:LED照明驅動器 26V StepUp Converter for 2-6 White LEDs RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1561ETA-T | 功能描述:LED照明驅動器 26V StepUp Converter for 2-6 White LEDs RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
| MAX1561EVKIT | 功能描述:LED 照明開發(fā)工具 Evaluation Kit for MAX1561 RoHS:否 制造商:Fairchild Semiconductor 產品:Evaluation Kits 用于:FL7732 核心: 電源電壓:120V 系列: 封裝: |
| MAX1562ESA | 功能描述:電源開關 IC - USB 4A USB Crnt-Limited w/Autoreset RoHS:否 制造商:Micrel 電源電壓-最小:2.7 V 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:SOIC-8 封裝:Tube |
發(fā)布緊急采購，3分鐘左右您將得到回復。