- 您現在的位置：買賣IC網 > PDF目錄180477 > MAX1748EUE+T (MAXIM INTEGRATED PRODUCTS INC) Triple-Output TFT-LCD DC-DC Converters PDF資料下載
參數資料
| 型號： | MAX1748EUE+T |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | Triple-Output TFT-LCD DC-DC Converters |
| 中文描述： | 2 A SWITCHING REGULATOR, 1250 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | 4.40 MM, 1.10 MM HEIGHT, 0.65 MM PITCH, EXPOSED PAD, TSSOP-16 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 278K |
| 代理商： | MAX1748EUE+T |
MAX1748
Triple-Output TFT LCD DC-DC Converter
______________________________________________________________________________________
13
voltage by connecting a voltage-divider from the output
(VNEG) to FBN to REF. Select R4 and R6 in the 50k
to
100k
range. Higher resistor values improve efficiency
at low output current but increase output voltage error
due to the feedback input bias current. Calculate the
remaining resistors with the following equations:
R3 = R4 [(VPOS / VREF) - 1]
R5 = R6 (VNEG / VREF)
where VREF = 1.25V. VPOS may range from VSUPP to
40V, and VNEG may range from 0 to -40V.
Flying Capacitor
Increasing the flying capacitor’s value reduces the out-
put current capability. Above a certain point, increasing
the capacitance has a negligible effect because the
output current capability becomes dominated by the
internal switch resistance and the diode impedance.
Start with 0.1F ceramic capacitors. Smaller values
may be used for low-current applications.
Charge-Pump Output Capacitor
Increasing the output capacitance or decreasing the
ESR reduces the output ripple voltage and the peak-to-
peak transient voltage. Use the following equation to
approximate the required capacitor value:
COUT
≥ [IOUT / (500kHz VRIPPLE)]
Charge-Pump Input Capacitor
Use a bypass capacitor with a value equal to or greater
than the flying capacitor. Place the capacitor as close
to the IC as possible. Connect directly to PGND.
Rectifier Diode
Use Schottky diodes with a current rating equal to or
greater than 4 times the average output current, and a
voltage rating at least 1.5 times VSUPP for the positive
charge pump and VSUPN for the negative charge pump.
PC Board Layout and Grounding
Careful printed circuit layout is extremely important to
minimize ground bounce and noise. First, place the
main boost converter output diode and output capacitor
less than 0.2in (5mm) from the LX and PGND pins with
wide traces and no vias. Then place 0.1F ceramic
bypass capacitors near the charge-pump input pins
(SUPP and SUPN) to the PGND pin. Keep the charge-
pump circuitry as close to the IC as possible, using
wide traces and avoiding vias when possible. Locate all
feedback resistive dividers as close to their respective
feedback pins as possible. The PC board should fea-
one point under the IC. To maximize output power and
efficiency and to minimize output power ripple voltage,
use extra wide power ground traces and solder the IC’s
power ground pin directly to it. Avoid having sensitive
traces near the switching nodes and high-current lines.
Refer to the MAX1748 evaluation kit for an example of
proper board layout.
Applications Information
Boost Converter Using a
Cascoded MOSFET
For applications that require output voltages greater
than 13V, cascode an external N-channel MOSFET
(Figure 4). Place the MOSFET as close to the LX pin as
possible. Connect the gate to the input voltage (VIN)
and the source to LX.
MOSFET Selection
Choose a MOSFET with an on-resistance (RDS(ON))
lower than the internal N-channel MOSFET. Lower
RDS(ON) will improve efficiency. The external N-channel
MOSFET must have a drain-voltage rating higher than
the main output voltage (VMAIN).
Chip Information
TRANSISTOR COUNT: 2846
相關PDF資料 |
PDF描述 |
|---|---|
| MAX1749EUK+T | SOT23 Vibrator Motor Driver |
| MAX174ACPI+ | Industry-Standard, 12-Bit ADC with Reference |
| MAX174ACWI+ | Industry-Standard, 12-Bit ADC with Reference |
| MAX174ACWI+T | Industry-Standard, 12-Bit ADC with Reference |
| MAX174AEPI+ | Industry-Standard, 12-Bit ADC with Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX1748EUE-TG069 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| MAX1748EVKIT | 功能描述:電源管理IC開發工具 MAX1748 Eval Kit RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| MAX17491GTA+ | 功能描述:功率驅動器IC Notebook MOSFET Driver RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX17491GTA+T | 功能描述:功率驅動器IC Notebook MOSFET Driver RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| MAX17495AATE+ | 制造商:Maxim Integrated Products 功能描述:- Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。