參數資料
型號： MAX19506ETM+T
廠商： Maxim Integrated Products
文件頁數： 27/35頁
文件大?。?/td> 0K
描述： IC ADC 8BIT 2CH 100MSPS 48TQFN
產品培訓模塊： Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝： 2,500
位數： 8
采樣率（每秒）： 100M
數據接口： 串行，并聯
轉換器數目： 2
功率耗散（最大）： 139mW
電壓電源： 模擬和數字
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 48-WFQFN 裸露焊盤
供應商設備封裝： 48-TQFN-EP（7x7）
包裝： 帶卷 (TR)
輸入數目和類型： 4 個單端，單極；2 個差分，單極
MAX19506
Dual-Channel, 8-Bit, 100Msps ADC
______________________________________________________________________________________
33
Small-Signal Noise Floor (SSNF)
SSNF is the integrated noise and distortion power in the
Nyquist band for small-signal inputs. The DC offset is
excluded from this noise calculation. For this converter, a
small signal is defined as a single tone with an amplitude
less than -35dBFS. This parameter captures the thermal
and quantization noise characteristics of the converter
and can be used to help calculate the overall noise figure
of a receive channel. Refer to www.maxim-ic.com for
application notes on Thermal + Quantization Noise Floor.
Signal-to-Noise Ratio (SNR)
For a waveform perfectly reconstructed from digital
samples, the theoretical maximum SNR is the ratio of
the full-scale analog input (RMS value) to the RMS
quantization error (residual error). The ideal, theoretical
minimum analog-to-digital noise is caused by quantiza-
tion error only and results directly from the ADC’s reso-
lution (N bits):
SNR[max] = 6.02 x N + 1.76
In reality, there are other noise sources besides quanti-
zation noise (e.g., thermal noise, reference noise, clock
jitter, etc.). SNR is computed by taking the ratio of the
RMS signal to the RMS noise. RMS noise includes all
spectral components to the Nyquist frequency exclud-
ing the fundamental, the first six harmonics (HD2–HD7),
and the DC offset.
Signal-to-Noise and Distortion (SINAD)
SINAD is computed by taking the ratio of the RMS sig-
nal to the RMS noise plus the RMS distortion. RMS
noise includes all spectral components to the Nyquist
frequency excluding the fundamental, the first six har-
monics (HD2–HD7), and the DC offset. RMS distortion
includes the first six harmonics (HD2–HD7).
Single-Tone Spurious-Free Dynamic Range
(SFDR1 and SFDR2)
SFDR is the ratio expressed in decibels of the RMS
amplitude of the fundamental (maximum signal compo-
nent) to the RMS amplitude of the next largest spurious
component, excluding DC offset. SFDR1 reflects the
spurious performance based on worst 2nd-order or
3rd-order harmonic distortion. SFDR2 is defined by the
worst spurious component excluding 2nd- and 3rd-
order harmonics and DC offset.
Total Harmonic Distortion (THD)
THD is the ratio of the RMS of the first six harmonics of
the input signal to the fundamental itself. This is
expressed as:
where V1 is the fundamental amplitude and V2–V7 are
the amplitudes of the 2nd-order through 7th-order
harmonics (HD2–HD7).
Third-Order Intermodulation (IM3)
IM3 is the total power of the third-order intermodulation
products to the Nyquist frequency relative to the total
input power of the two input tones fIN1 and fIN2. The
individual input tone levels are at -7dBFS. The third-
order intermodulation products are: 2 x fIN1 - fIN2, 2 x
fIN2 - fIN1, 2 x fIN1 + fIN2, 2 x fIN2 + fIN1.
Aperture Delay
The input signal is sampled on the rising edge of the
sampling clock. There is a small delay between the ris-
ing edge of the sampling clock and the actual sampling
instant, which is defined as aperture delay (tAD).
Aperture Jitter
Aperture jitter (tAJ) is defined as the sample-to-sample
time variation in the aperture delay.
Overdrive Recovery Time
Overdrive recovery time is the time required for the
ADC to recover from an input transient that exceeds the
full-scale limits. The specified overdrive recovery time is
measured with an input transient that exceeds the full-
scale limits by ±10%.
Chip Information
PROCESS: CMOS
THD
VVV
V
log
=×
++
+++
20
2
3
2
4
2
5
2
6
2
7
2
1
SINAD
NOISE
DISTORTION
SIGNAL
RMS
log
=×
+
20
22
SNR
SIGNAL
NOISE
RMS
log
=×
20
相關PDF資料
PDF描述
MAX19515ETM+T IC ADC 10BIT 2CH 65MSPS 48TQFN
MAX19516ETM+T IC ADC 10BIT 2CH 100MSPS 48TQFN
MAX19700ETM+T IC ANLG FRNT END 48-TQFN
MAX19705ETM+ IC ANLG FRNT END 48-TQFN
MAX19706ETM+T IC ANLG FRNT END 48-TQFN
相關代理商/技術參數
參數描述
MAX19506EVKIT+ 功能描述:數據轉換 IC 開發工具 MAX19505-07/15-17 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX19507ETM+ 功能描述:模數轉換器 - ADC 8-Bit 2Ch 130Msps 1.8V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX19507ETM+T 功能描述:模數轉換器 - ADC 8-Bit 2Ch 130Msps 1.8V Precision ADC RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32
MAX19507EVKIT+ 功能描述:數據轉換 IC 開發工具 MAX19505-07/15-17 Eval Kit RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V
MAX1950ETM 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*