參數資料
型號: MAX2037CCQ+T
廠商: Maxim Integrated Products
文件頁數: 2/13頁
文件大?。?/td> 0K
描述: IC AMP VARIABLE GAIN 100-TQFP
產品培訓模塊: Lead (SnPb) Finish for COTS
Obsolescence Mitigation Program
標準包裝: 250
類型: 可變?cè)鲆娣糯笃?br>
應用: 醫療用超聲波成像,聲納
安裝類型: 表面貼裝
封裝/外殼: 100-TQFP 裸露焊盤
供應商設備封裝: 100-TQFP-EP(14x14)
包裝: 帶卷 (TR)
Applications Information
External Compensation
External compensation is required for bypassing inter-
nal biasing circuitry. Connect, as close as possible,
individual 4.7F capacitors from each pin EXT_C1,
EXT_C2, and EXT_C3 (pin 13, 14, 15) to ground.
External Bias Resistor
An external resistor at EXT_RES is required to set the
bias for the internal biasing circuitry. Connect, as close
as possible, a 7.5k
Ω resistor from EXT_RES (pin 38) to
ground.
Analog Input and Output Coupling
In typical applications, the MAX2037 is being driven
from a low-noise amplifier (such as the MAX2034) and
is typically driving a discrete differential anti-alias filter
into an ADC (such as the MAX1436 octal ADC). The
differential input impedance of the MAX2037 is typically
200
Ω. The differential outputs are capable of driving a
differential load resistance of 1000
Ω. The output
impedance is 100
Ω differential. The differential outputs
have a common-mode bias of approximately 3.0V. AC-
couple these differential outputs if the next stage has a
different common-mode input range.
Ultrasound-Specific IMD3 Specification
Unlike typical communications specs, the two input
tones are not equal in magnitude for the ultrasound-
specific IMD3 two-tone specification. In this measure-
ment, f1 represents reflections from tissue and f2
represents reflections from blood. The latter reflections
are typically 25dB lower in magnitude, and hence the
measurement is defined with one input tone 25dB lower
than the other. The IMD3 product of interest (f1 - (f2 - f1))
presents itself as an undesired Doppler error signal in
ultrasound applications. See Figure 1.
Board Layout
The pin configuration of the MAX2037 is optimized to
facilitate a very compact physical layout of the device
and its associated discrete components. A typical
application for this device might incorporate several
devices in close proximity to handle multiple channels
of signal processing.
The exposed pad (EP) of the MAX2037’s TQFP-EP
package provides a low thermal-resistance path to the
die. It is important that the PCB on which the MAX2037
is mounted be designed to conduct heat from the EP.
In addition, provide the EP with a low-inductance path
to electrical ground. The EP MUST be soldered to a
ground plane on the PCB, either directly or through an
array of plated via holes.
MAX2037
Ultrasound Variable-Gain Amplifier
10
______________________________________________________________________________________
-25dB
ULTRASOUND
IMD3
f1 - (f2 - f1)f2 + (f2 - f1)
f1
f2
Figure 1. Ultrasound IMD3 Measurement Technique
相關PDF資料
PDF描述
MAX3861ETG+T IC AMP POST W/AGC 24-TQFN-EP
VE-2TV-IV-F3 CONVERTER MOD DC/DC 5.8V 150W
MAX9000ESA+ IC OP AMP LP HI SPEED 8-SOIC
VE-2TV-IV-F2 CONVERTER MOD DC/DC 5.8V 150W
VI-252-IV-F1 CONVERTER MOD DC/DC 15V 150W
相關代理商/技術參數
參數描述
MAX2037CCQ-TD 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Ultrasound Variable-Gain Amplifier
MAX2037EVKIT 制造商:Maxim Integrated Products 功能描述:ULTRASOUND VARIABLE-GAIN AMPLIFIER - Rail/Tube
MAX2038 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Ultrasound VGA Integrated with CW Octal Mixer
MAX2038CCQ+ 功能描述:儀表放大器 Ultrasound Variable Gain Amplifier RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比(最小值):88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk
MAX2038CCQ+D 制造商:Maxim Integrated Products 功能描述:MAXIM MAX2038CCQ+D AMPLIFIERS - Trays 制造商:Maxim Integrated Products 功能描述:Maxim MAX2038CCQ+D Amplifiers