- 您現在的位置：買賣IC網 > PDF目錄9553 > MAX211EWI (Maxim Integrated Products)IC TXRX RS232 5V 28-SOIC PDF資料下載
參數資料
| 型號： | MAX211EWI |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 21/23頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC TXRX RS232 5V 28-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 25 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 4/5 |
| 規程： | RS232 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
+5V, RS-232 Transceivers
with 0.1F External Capacitors
Shutdown and Enable Control
In shutdown mode, the MAX200/MAX205/MAX206/
MAX211/MAX213 charge pumps are turned off, V+ is
pulled down to VCC, V- is pulled to ground, and the
transmitter outputs are disabled. This reduces supply
current typically to 1A (15A for the MAX213). The time
required to exit shutdown is 1ms, as shown in Figure 5.
All receivers except R4 and R5 on the MAX213 are put
into a high-impedance state in shutdown mode. The
MAX213’s R4 and R5 receivers still function in shutdown
mode. These two receivers are useful for monitoring
external activity while maintaining minimal power con-
sumption.
The enable control is used to put the receiver outputs
into a high-impedance state, so that the receivers can be
connected directly to a three-state bus. It has no effect
on the RS-232 drivers or on the charge pumps.
MAX213 Receiver Operation in Shutdown
During normal operation, the MAX213’s receiver propa-
gation delay is typically 1Fs. When entering shutdown
with receivers active, R4 and R5 are not valid until 80Fs
after SHDN is driven low. In shutdown mode, propaga-
tion delays increase to 4Fs for a high-to-low or a low-to-
high transition.
When exiting shutdown, all receiver outputs are invalid
until the charge pumps reach nominal values (
< 2ms
when using 0.1FF capacitors).
Figure 5. Transmitter Outputs When Exiting Shutdown
Table 1a. MAX200 Control Pin Configurations
Table 1b. MAX205/MAX206/MAX211 Control Pin Configurations
Table 1c. MAX213 Control Pin Configurations
*Active = active with reduced performance.
TWO TRANSMITTER
OUTPUTS:
ONE HIGH, ONE LOW
SHDN*
THREE TRANSMITTERS LOADED WITH 3kI||2500pF.
*SHUTDOWN POLARITY REVERSED FOR MAX213.
SHUTDOWN
TRANSMITTERS ON
SHDN
OPERATION STATUS
TRANSMITTERS T1–T5
0
Normal Operation
All Active
1
Shutdown
All High-Z
SHDN
EN
OPERATION STATUS
TRANSMITTERS T1–T5
RECEIVERS R1–R5
0
Normal Operation
All Active
0
1
Normal Operation
All Active
All High-Z
1
0
Shutdown
All High-Z
SHDN
EN
OPERATION STATUS
TRANSMITTERS T1–T4
RECEIVERS
R1, R2, R3
R4, R5
0
Shutdown
All High-Z
High-Z
0
1
Shutdown
All High-Z
High-Z
Active*
1
0
Normal Operation
All Active
High-Z
1
Normal Operation
All Active
Active
MAX200–MAX209/MAX211/MAX213
Maxim Integrated
7
相關PDF資料 |
PDF描述 |
|---|---|
| IDT74CBTLV3257PGG | IC MUX/DEMUX 2:1 QUAD LV 16TSSOP |
| MAX211EEAI | IC TXRX RS232 5V 28-SSOP |
| CS3100A-36-78S | CONN RCPT 14POS WALL MNT W/SCKT |
| D38999/24WJ19SA | CONN RCPT 19POS JAM NUT W/SCKT |
| D38999/24KD19PA | CONN RCPT 19POS JAM NUT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MAX211EWI+ | 功能描述:RS-232接口集成電路 5V RS232 Transceiver w/0.1uF External Cap RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX211EWI+T | 功能描述:RS-232接口集成電路 5V RS232 Transceiver w/0.1uF External Cap RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX211EWI-T | 功能描述:RS-232接口集成電路 RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| MAX211I | 制造商:TI 制造商全稱:Texas Instruments 功能描述:5-V MULTICHANNEL RS-232 LINE DRIVER/RECEVER |
| MAX211IDB | 功能描述:RS-232接口集成電路 5V MultiCh Line Driver/Receiver RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
發布緊急采購，3分鐘左右您將得到回復。